Remote Control Via Lc-3 Or Lc-9Rtx; Operation Via Dmx Light Controller; Dmx Connection - IMG STAGELINE LED-640RGBW Mode D'emploi

b) Activate the menu item
GB
ENTER. The slave mode adjusted starts
flashing on the display:
Slave mode 1: The slave unit is syn-
chronized with the master unit.
Slave mode 2: The slave unit is tem-
porarily controlled opposite to the
master unit.
c) Press the button
slave mode. To memorize, press the button
ENTER.
d) To exit the setting mode, keep the button
MENU pressed until the unit starts the show
program or wait for one minute.
Once the slave units receive the control signals
from the master unit, the red LED SLAVE (7)
lights up on the slave units.

5.5 Remote control via LC-3 or LC-9RTX

The cable remote controller LC-3 or the wireless
remote controller LC-9RTX available as an acces-
sory allows to control different functions.
1) Connect the remote controller LC-3 to the jack
ONLY FOR REMOTE CONTROL (10) or con-
nect the wireless receiver of the LC-9RTX to the
jack ONLY FOR WIRELESS RECEIVER (9).
2) No DMX signal must be present at the DMX
INPUT (12). The yellow LED MASTER (4) must
light up.
3) The DMX OUTPUT (13) allows to connect fur-
ther LED-640RGBW (
control them together with the master unit via the
remote controller.
4) To activate or deactivate the light, press the but-
ton STAND BY on the remote controller. With the
light switched off, the LED of the button STAND
BY lights up as an indication.
5) Press the button MODE on the remote controller
to select the operating mode:
1. If the LED of the button MODE does not light
up, keep the button FUNCTION on the
remote controller pressed to activate one of
the four stroboscope functions:
– stroboscope with all LEDs
– stroboscope with changing colours and
colour combinations
– music-controlled stroboscope with all LEDs
For this purpose, the music control must
be switched on (
– music-controlled stroboscope with alter-
nating colours and colour combinations
For this purpose, the music control must
be switched on (
16
with the button
or to select the desired
chapter 5.4) in order to
chapter 5.1).
chapter 5.1).
By keeping the button FUNCTION pressed
again, the next stroboscope function is acti-
vated in each case. If the button FUNCTION
is not pressed, the show program last
selected will be activated.
2. If the LED of the button MODE lights up,
select the show program (Sh 1 – 12) with the
button FUNCTION.
3. If the LED of the button MODE flashes slowly,
it is possible to select a colour or colour com-
bination with the button FUNCTION.
4. If the LED of the button MODE flashes quickly,
it is possible to select the speed for the auto-
matic program run (3 speeds).

6 Operation via DMX light controller

For operation via a light controller with DMX-512
protocol (e. g. DMX-1440 or DMX-510USB from
"img Stage Line"), the LED-640RGBW is equipped
with 4 DMX control channels. For the functions and
the DMX values see chapter 9.2.
DMX is the abbreviation of digital multiplex and means
digital control of several DMX units via a common control
cable.

6.1 DMX connection

For DMX connection, 3-pole XLR connectors with
the following pin configuration are provided:
pin 1 = ground, 2 = DMX-, 3 = DMX+
For connection, special cables for high data flow
are recommended. Standard microphone cables
with screening and a minimum cross section of 2 ×
0.22 mm 2 and with a capacity as low as possible
can only be recommended for a total cable length
of up to 100 m. For cable lengths exceeding 150 m,
it is generally recommended to insert a DMX level
matching amplifier (e. g. SR-103DMX from "img
Stage Line").
1) Connect the DMX input (12) to the DMX output
of the light controller.
2) Connect the DMX output (13) to the DMX input
of the following light effect unit; connect its out-
put again to the input of the following unit, etc.
until all light effect units have been connected in
a chain.
3) To prevent interference in signal transmission, in
case of long cables or a multitude of units con-
nected in series, terminate the DMX output of
the last DMX unit in the chain with a 120 Ω resis-
tor (> 0.3 W): Connect a corresponding termi-
nating plug (e. g. DLT-123 from "img Stage
Line") to the output jack.