Bosch GCM 12 SD Professional Notice Originale page 35

OBJ_BUCH-1130-003.book Page 35 Friday, December 5, 2014 12:37 PM
Adjusting: (see figure W2)
– Loosen the locking screws 22 on bothe sides of the fence
extensions 21.
Loosen the setting screws 67 with the supplied hex key 35
(4 mm).
– Remove the fence extensions.
– Loosen all hex socket screws 68 with the supplied socket
spanner 35 (14 mm).
– Turn the fence 20 until the angle gauge is flush over the
complete length.
– Retighten the hex socket screws 68.
– Retighten the fence extensions. Tighten the setting screws
67 only to the extent, that the fence extensions can be
moved easily.
Transport (see figure X)
Before transporting the power tool, the following steps must
be carried out:
– Loosen the locking screw 31 if tightened. Pull the tool arm
completely to the front and tighten the locking screw
again.
– Bring the machine into the transport position.
– Remove all accessories that cannot be mounted firmly to
the power tool.
If possible, place unused saw blades in an enclosed con-
tainer for transport.
– Carry the power tool by the transport handles 30 and 4 or
via the recessed grips 69 on the side of the saw table.
 When transporting the power tool, use only the trans-
port devices and never use the protective devices.
 The power tool should always be carried by two per-
sons in order to avoid back injuries.
Maintenance and Service
Maintenance and Cleaning
 Before any work on the machine itself, pull the mains
plug.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
Cleaning
For safe and proper working, always keep the power tool and
its ventilation slots clean.
The retracting blade guard must always be able to move freely
and retract automatically. Therefore, always keep the area
around the retracting blade guard clean.
Remove dust and chips after each working procedure by
blowing out with compressed air or with a brush.
Clean the roller 11 regularly.
Bosch Power Tools
Accessories
Quick-action clamp
Vertical. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 608 040 205
Horizontal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 608 040 236
Insert plates. . . . . . . . . . . . . . . . . . . . . . . . . . . 2 607 960 020
Dust bag set. . . . . . . . . . . . . . . . . . . . . . . . . . . 2 605 411 211
Extension bars (435 mm) . . . . . . . . . . . . . . . 2 607 001 956
Saw blades for wood and plate materials,
panels and strips/mouldings
Saw blade 305 x 30 mm, 60 teeth . . . . . . . . 2 608 640 441
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can
also be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
English | 35
1 609 92A 0XM | (5.12.14)