Milwaukee CS60 Notice Originale page 19

Technical Data
Circular saw
Production code
Rated input
No-load speed
Saw blade dia. x hole dia
Max. Cutting depth at 90° / 45° / 56°
Weight according EPTA-Procedure 01/2003
Noise information
Measured values determined according to EN 60745. Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A))
Sound power level (Uncertainty K=3dB(A))
Wear ear protectors!
Vibration information
Vibration total values (triaxial vector sum) determined according to EN 60745
Sawing of wood: Vibration emission value a
Uncertainty K=
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and
may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for di erent applications, with
di erent accessories or poorly maintained, the vibration emission may di er. This may signi cantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched o or when it is running
but not actually doing the job. This may signi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the e ects of vibration such as: maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.
WARNING! Read all safety warnings, instructions,
illustrations and speci cations provided with this power tool.
Failure to follow the warnings and instructions may result in electric
shock, re and/or serious injury.
Save all warnings and instructions for future reference.
CIRCULAR SAW SAFETY WARNINGS
Cutting procedures
a) DANGER: Keep hands away from cutting area and
the blade. Keep your second hand on auxiliary handle, or
motor housing. If both hands are holding the saw, they cannot be
cut by the blade.
b) Do not reach underneath the workpiece. The guard cannot
protect you from the blade below the workpiece.
c) Adjust the cutting depth to the thickness of the workpi-
ece. Less than a full tooth of the blade teeth should be visible below
the workpiece.
d) Never hold the workpiece in your hands or across your leg
while cutting. Secure the workpiece to a stable platform. It is
important to support the work properly to minimise body exposure,
blade binding, or loss of control.
h,w
e) Hold the power tool by insulated gripping surfaces, when
performing an operation where the cutting tool may contact
hidden wiring or its own cord. Contact with a „live" wire will also
make exposed metal parts of the power tool „live" and could give the
operator an electric shock.
f) When ripping, always use a rip fence or straight edge
guide. This improves the accuracy of cut and reduces the chance of
blade binding.
g) Always use blades with correct size and shape (diamond
versus round) of arbour holes. Blades that do not match the
mounting hardware of the saw will run o -centre, causing loss of
control.
h) Never use damaged or incorrect blade washers or bolt.
The blade washers and bolt were specially designed for your saw, for
optimum performance and safety of operation.
Kickback causes and related warnings
– kickback is a sudden reaction to a pinched, jammed or misaligned
saw blade, causing an uncontrolled saw to lift up and out of the
workpiece toward the operator;
– when the blade is pinched or jammed tightly by the kerf closing
down, the blade stalls and the motor reaction drives the unit rapidly
back toward the operator;
CS 60
4290 71 03 ...
4108 66 03 ...
4192 26 03 ...
... 000001-999999
1600 W
6300 min
-1
184 x 30 mm
61 / 49 / 35 mm
4,8 kg
92,5 dB(A)
103,5 dB(A)
GB
2,3 m/s
2
1,5 m/s
2
English
17