Publicité
Les langues disponibles
Les langues disponibles
WARNING: To reduce the risk of injury, turn planer off, disconnect the tool from the
power source before assembling the planer to the stand. An accidental start-up can cause
injury.
WARNING: For your own safety, it is recommended that two people carry this machine or serious
injury could result.
Your planer stand is set up to accept the DW733, DW734 or DW735 D
1. Carefully lift and place the planer on the MDF top (L).
2. Align the holes in the planer base with corresponding holes on the MDF top.
3. Insert four 75 mm hex head bolts (N) through the planer and base and secure them with the flat
washers (S) and nuts (T) provided.
IF YOU DO NOT HAVE A D
WALT PLANER, BUT WISH TO USE
E
THE DW7350 MOBILE PLANER STAND:
WARNING: Center your planer on the stand. Failure to center the
planer could lead to an unstable assembly. Serious injury could result.
1. Mark the placement of the holes on the MDF top (L).
2. Drill marked holes in the MDF top.
3. Attach your planer to the MDF top with the hex head bolts (N), flat
washers (S), and nuts (T) provided.
NOTE: Do not drill more than 4 holes. One bolt per corner is sufficient.
Properly sized hardware (obtained locally) may be required to securely
attach the planer (if not D
WALT) to the MDF top.
E
WARNING: Planers MUST be mounted in the orientation shown in
Figure 3.
IMPORTANT: The planer MUST be positioned so the tool is bolted
squarely to the MDF top. If this is not possible, please call 1-800-4-D
technical assistance.
WARNING: Any tool used with this stand must be properly positioned and secured to ensure
stability and to prevent inadvertent tipping.
To Adjust the Rubber Leveling Feet
The two rubber feet (F) of the mobile planer stand are installed for additional support on slightly
uneven floors.
1. Loosen the 2 nuts that hold one of the rubber feet of the mobile base.
2. Grasp the nuts with a wrench and turn the foot until it is extended or retracted to the level
required.
3. Re-tighten the bolts.
4. Repeat for the other rubber foot.
NOTE: Once assembly is complete and before first use, check each bolt and nut to ensure it is
properly tightened, and that all mechanisms operate properly.
OPERATION
WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect
tool from power source before installing and removing accessories, before adjusting or
changing set-ups or when making repairs. An accidental start-up can cause injury.
Make sure the planer stand is firmly on the floor, the foot pedal down and the wheel raised before
use.
WARNING: Do not attempt to move the planer on the stand if the planer is not bolted down.
Serious personal injury may result.
To Move Planer Stand
1. Step on the foot pedal to unlock and lift stand.
2. Firmly grasp the handles on your planer. Move to a new location.
3. Push the foot pedal up, dropping the base into a locked position before you resume planing.
CAUTION: Use caution when moving the planer stand. Tipping can occur if wheels are stopped
WALT thickness planers.
abruptly by encountering debris on the floor or other irregularities in travel path.
E
MAINTENANCE
WARNING: To reduce the risk of injury, turn unit off and disconnect it from power source
before installing and removing accessories, before adjusting or when making repairs. An
accidental start-up can cause injury.
FIG. 3
Cleaning
WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the
tool. These chemicals may weaken the plastic materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid get inside the tool; never immerse any part of the
tool into a liquid.
Accessories
WARNING: Since accessories, other than those offered by D
this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury,
only D
WALT recommended accessories should be used with this product.
E
Recommended accessories for use with your tool are available at extra cost from your local dealer or
authorized service center. If you need assistance in locating any accessory, please contact D
Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-D
9258) or visit our website: www.dewalt.com.
Repairs
WALT (1-800-433-9258) for
E
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush
inspection and replacement) should be performed by a D
authorized service center or other qualified service personnel. Always use identical replacement
parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRANTY SERVICE: Registering your product will help you obtain more efficient warranty
service in case there is a problem with your product.
• CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as fire, flood or theft,
your registration of ownership will serve as your proof of purchase.
• FOR YOUR SAFETY: Registering your product will allow us to contact you in the unlikely event
a safety notification is required under the Federal Consumer Safety Act.
Register online at www.dewalt.com/register.
Three Year Limited Warranty
D
WALT will repair, without charge, any defects due to faulty materials or workmanship for three
E
years from the date of purchase. This warranty does not cover part failure due to normal wear or tool
abuse. For further detail of warranty coverage and warranty repair information, visit www.dewalt.com
or call 1-800-4-D
caused where repairs have been made or attempted by others. This warranty is the only warranty
offered by D
any incidental or consequential damages. This warranty gives you specific legal rights and you may
have other rights which vary in certain states or provinces. Some states do not allow the exclusion
or limitation of incidental or consequential damages, or limitations on how long an implied warranty
lasts, so the above limitations or exclusions may not apply to you.
3
WALT (1-800-433-9258). This warranty does not apply to accessories or damage
E
WALT, and any implied warranties shall not apply. D
E
WALT, have not been tested with
E
WALT
E
WALT (1-800-433-
E
WALT factory service center, a D
WALT
E
E
WALT will not be responsible for
E
Publicité
