Assembly And Operation - HERKULES ZGS 3300 UG Mode D'emploi D'origine

Anleitung_ZGS_3300_UG_SPK7:_
GB
Use the same procedure to set the stop to 45°,
but instead move the cutting head to the left and
use the left screw (e).
6.2 Setting the stop face (Fig. 12)
Lower the cutting head and press in the locking
button (16). Make sure that the table shows a
miter angle of 0°.
Place an angular stop against the stop face and
the saw blade.
If the blade does not touch the angular stop,
undo the three screws (33).
Adjust the stop face so that it touches the angle
gage full-face. Retighten the screws.

7. Assembly and operation

Always place the workpiece against the stop face. A
twisted and bent workpiece that cannot be held flat
on the table or against the stop face may catch on
the blade and should not be used. Keep your hands
out of the sawing zone. The entire table area is out of
bounds for hands. It is marked with "No Hands"
signs.
7.1 Fitting the clamping device and extension
supports (Fig. 1/3/4)
Always use the clamping device (19) to secure
the workpiece in position. Insert the clamping
device in one of the mounts (30) provided and
fasten it in place with the clamping screw.
Insert the extension supports on the left and right
in the mounts (29) provided in the base plate
and tighten the clamping screw.
The standard end stop (18) can be used for
repeat cuts. In this case, slip the end stop onto
one of the extension supports and adjust with the
clamping screw.
7.2 Fitting the dust extraction device
(Fig. 10/11/12)
Mount the dust extraction nozzle (28) in the outlet
opening under the cutting arm.
Mount the big end of the angle piece (35) on the
back of the crosscut and miter saw at the outlet
opening. The angle piece has to point to the side
or down.
On the angle piece you can either attach the dust
bag (24) or a suction hose for drawing off the saw
dust.
Mount the second angle piece on the upper dust
extraction socket (34) and plug on the suction
hose (26).
With With the Y-piece (27) you can join together
the upper and lower suction hose. Plug the hose
12
27.04.2011 11:22 Uhr Seite 12
with adaptor (a) on the outlet of the Y-piece. You
can now connect a suitable dust extractor to the
adaptor.
7.3 Setting up the saw unit (Fig. 1/2)
To adjust the turntable (8), loosen the locking grip
(10) by approx. 2 turns, which frees the turntable
(8).
Turn the turntable (8) and scale pointer (11) to
the desired angular setting on the dial (12) and
lock into place with the locking grip (10).
To release the saw from its position at the bottom
(transport position), pull the retaining pin (16) out
of the motor mounting while pressing down lightly
on the machine head (4).
Swing the machine head (4) up until the retaining
hook latches into place.
When the tightening screw (13) is loosened, you
can tilt the machine head (4) to the left by up to
45°.
Warning!
Never connect the plug to a power source before
you have completed all the installation work,
made all the necessary settings, and read and
understood all the safety and operating
instructions.
7.4 Crosscut 90° and turntable 0° (Fig. 8)
For cutting widths up to 170 mm it is possible to fix
the saw's drag function with the thumb screw (14) in
rear position. If the cutting width exceeds 170 mm
you must ensure that the thumb screw (14) is
slackened and that the machine head (4) can be
moved.
Move the machine head (4) to its upper position.
Use the handle (2) to push back the machine
head (4) and fix it in this position if required
(dependent on the cutting width).
Place the piece of wood to be cut against the
stop rail (7) and on the turntable (8).
Lock the material with the clamping device (19)
on the base plate (9) to prevent the material from
moving during the cutting operation.
Push down the release lever (1) to release the
machine head (4).
Press the ON/OFF switch (3) to start the motor.
Use the handle (2) to apply steady and light
downward pressure to cut all the way through the
workpiece.
When the cutting operation is completed, move
the machine head back to its upper (home)
position and release the ON/OFF button (3).
Important! The integral resetting springs will
automatically lift the machine head. Do not simply
let go of the handle (2) after cutting, but allow the