English; Introduction - ATT NUSSBAUM POWER LIFT HF 3S 3000 Manuel D'exploitation

ENGLISH

Introduction

Nussbaum products are a result of many years of
experience. A high quality standard and superior
concept guarantees you reliability, long lifetimes
and economical operation. To prevent unnec-
essary damage and hazards, read this operating
manual carefully and always comply with its con-
tents.
Any other use, or use beyond purpose is considered
improper.
The HYMAX lifts listed in this manual are identical in
construction to the listed Nussbaum lifts. This manu-
al applies to the following lifts:
POWER LIFT HF 3S 3000
POWER LIFT HF 3S 3500
POWER LIFT HF 3S 4000
Nussbaum is not liable for any resulting dam-
!
age. The operating company alone carries the
risk.
Proper use also includes:
• Adherence to all instructions in this operating
manual and
• Compliance with inspection and maintenance
work and the inspections stipulated.
• The operating manual is to be followed by all per-
sonnel working on the lift. This is notably with re-
gards to Section 4 "Safety conditions".
• In addition to safety information from the operat-
ing manual, comply with rules and regulations at
the location of use.
• Proper system handling.
Operating company obligations:
The operating company is obliged to only permit
personnel to work on the system who
• Understand the principle regulations about work
safety and accident prevention and who have
been trained in working with the lift.
• Have read the safety section and warning infor-
mation in this operating manual, have under-
stood it and confirmed learning with a signature.
Hazards in working with the system:
Nussbaum products have been designed and built
to state-of-the-art and to recognised safety stan-
dards. However, improper use may lead to hazards
to life and limb of the user or result in property dam-
age.
The system may only be operated
• For proper intended use.
• If it is technically in perfect condition.
= HYMAX HF 3S 3000
= HYMAX HF 3S 3500
= HYMAX HF 3S 4000
Original Operating Manual
Organisational measures
• The operating manual is always to be kept ready
at the location of use of the system.
• Supplemental to the operating manual, refer to
and comply with generally valid legal and other
binding regulations for accident prevention and
for environmental protection.
• Check occasionally that personnel have an
awareness of hazards and safe work in compli-
ance with the operating manual!
• Use personal protective equipment as needed or
required by regulations.
• All safety and hazard information on the system is
to be kept in a legible condition!
• Replacement parts must meet technical specifi-
cations of the manufacturer. This is only guaran-
teed for original parts.
• Deadlines pre-set or given in the operating man-
ual for repeating tests / inspections must be fol-
lowed.
Maintenance work, error removal
Comply with pre-determined setting, maintenance
and inspection work and intervals in the operating
manual, including details for exchanging parts /
part fittings! These activities may only be done by
specialists who have participated in a special fac-
tory training.
Guarantee and liability
• In principle, our "General sales and supply condi-
tions" apply.
Guarantee and liability claims for personal and
property damage are excluded if due to one or
more of the following causes:
• Improper use of the system.
• Improper assembly, commissioning, operation
and maintenance of the system.
• Operating the system with defective safety de-
vices or improperly attached or non-functional
safety and protection devices.
• Non-compliance with information in the operat-
ing manual in terms of transport, storage, assem-
bly, commissioning, operation, maintenance and
fitting of the system.
• Independent construction changes to the system.
• Independent changes to ..... (e.g. drive ratios:
power, rotation speed, etc.).
• Improperly done repairs.
• Catastrophic cases due to foreign influences or
force majeure.