IMG STAGELINE FM-1008 Mode D'emploi page 8

A bottle of fragrance (contents 25 ml) is sufficient for
GB
5 litres of fog fluid. Never add more fragrance as other-
wise the fog machine may clog.
WARNING
Never add flammable fluids of any kind!
Explosion hazard!
CAUTION
While filling up fog fluid, the unit must not be
connected to the mains. Disconnect the mains plug
from the socket first!
The unit is not splashproof. If fluid accidentally gets
inside the unit, do not set the fog machine into op-
eration; it must be cleaned and checked by skilled
personnel first.
1) Unscrew the tank cap (2).
2) Fill up the fog fluid. If any fluid is spilt, wipe it off
immediately with a dry cloth. It must not get inside
the unit.
3) Tightly close the tank. Make sure that the suction
hose will reach the bottom of the tank.
4.2 Setting up and operating the unit
CAUTION
During operation the fog output nozzle will become
very hot (300 °C). Never touch it and always
ensure a sufficient distance (minimum distance
50 cm) to easily flammable material or material
sensitive to heat.
The fog stream is hot; position the unit in such a
way that the fog stream will not directly hit anyone
– risk of burning!
To prevent heat accumulation within the unit, select
a place which ensures a sufficient air circulation
during operation. Never cover the air vents of the
housing (e.g. by curtains). Keep a minimum
distance of 20 cm to any other objects.
Never operate the fog machine without fog fluid.
Fire hazard due to overheating. Besides, the unit
may be damaged.
1) Remove the complete packaging material. Make
sure that there are no packaging remnants at the
fog output nozzle.
2) There must be a sufficient quantity of fog fluid in the
fog machine. Check the fluid level of the tank and
fill up fog fluid, if necessary – see chapter 4.1.
3) Place the unit on a horizontal surface or mount it via
its bracket (1) [e.g. on a cross arm via a mounting
clip]. To adjust the unit, release the two screws (3)
on the mounting bracket, place the unit in a hori-
zontal position, if possible, and retighten the two
screws. For a reliable operation, the maximum in-
clination of the fog machine must not exceed 15°!
8
WARNING The unit must be mounted safely
and expertly. If it is installed as a sus-
pended load above persons, it must
additionally be secured (e.g. by a
safety rope; fasten the safety rope in
such a way that the maximum falling
distance of the unit is 20 cm).
Fog machines will develop condensation around
the fog output nozzle. Thus, when selecting a
mounting place, take into account that moisture will
accumulate below the nozzle.
4) Connect the plug (12) of the remote control to the
jack (4) on the rear side of the fog machine.
5) Connect the unit to a socket (230 V~ / 50 Hz) via
the mains cable (6). Thus, it is switched on. The fog
machine will heat up for approx. 4.5 minutes.
During the heating process, the LEDs READY (8)
and POWER (9) on the remote control keep flash-
ing and the unit will not yet be able to emit any fog.
6) Once the LED READY (8) stops flashing and starts
to light permanently, the heating process is com-
pleted and fog may be emitted.
Manual fog output:
Turn the control (10) counter-clockwise until it
locks. The LED TIMER (7) will not light up. Keep the
button (11) on the remote control pressed. Fog will
be emitted while it is kept pressed.
Automatic fog output:
Set the control (10) from the left stop to the desired
fog output interval. In this case, the fog output time
is fixed to approx. 3 seconds; the interval between
the outputs can be set from 5 to 200 seconds. The
more the control is turned clockwise, the longer the
interval is between the outputs. The LED TIMER (7)
will light up in the automatic mode. To terminate the
fog output, turn the control counter-clockwise until it
locks at the left stop. The LED TIMER will be extin-
guished. In the automatic mode, fog may be emit-
ted additionally by pressing the button (11).
Note: Due to residual fluid in the fog machine, the
unit may still emit some fog after releasing
the button or after switching off the automatic
mode.
7) The unit is able to emit fog continuously until the
LED READY (8) starts flashing again. Then it must
heat up again. During the heating process, the unit
will not be able to emit any fog.
8) To switch off the fog machine after operation, dis-
connect the plug of the mains cable (6) from the
socket.
Note: Due to residual fluid in the fog machine, the
unit may still emit some fog for a short time
after switching off.
9) Before transporting the unit, allow it to cool and
completely empty the tank!