Working Advice; Maintenance And Service; Maintenance And Cleaning; After-Sales Service And Application Service - Bosch AdvancedImpact 18 QuickSnap Notice Originale

OBJ_BUCH-3177-001.book Page 19 Monday, June 12, 2017 10:35 AM
to the material or when the adjusted torque is reached. The
safety clutch is deactivated in the "
drilling.
Select a higher setting or switch to the "
screwing screws.
Setting the operating mode (see figure J)
The operating mode preselection ring 3 can be used to
choose between screwdriving, drilling and impact drilling.
In the "Impact drilling" position, the safety clutch is deactivat-
ed and the maximum power is always effective.
Gear selection, mechanical
 Actuate the gear selector 4 only when the machine is at
a standstill.
Two speed ranges can be preselected with the gear selector
4.
Gear 1:
Low speed range; for screwdriving or for working with a large
drilling diameter.
Gear 2:
High speed range; for working with a small drilling diameter.
 Always push the gear selector through to the stop. Oth-
erwise, the machine can become damaged.
Switching On and Off
To start the machine, press the On/Off switch 10 and keep it
pressed.
The work light 7 illuminates when the On/Off switch 10 is
lightly or fully pressed and allows the illumination of the work
area in poor lighting conditions.
The worklight 7 will remain lit for approx. 10 seconds when
the On/Off switch 10 has been released.
To save energy, only switch the power tool on when using it.
Setting the Speed/Impact Rate
The speed/impact rate of the switched on power tool can be
variably adjusted, depending on how far the On/Off switch 10
is pressed.
Light pressure on the On/Off switch 10 results in low speed/
impact rate. Further pressure on the switch increases the
speed/impact rate.
Fully automatic spindle locking (Auto-lock)
The drill spindle and therefore the mounting are locked when
the On/Off switch 10 is not pressed.
This enables screws to be screwed in, even when the battery
is empty and allows for the machine to be used as a screwdriv-
er.
Temperature Dependent Overload Protection
When using as intended for, the power tool cannot be subject
to overload. When the load is too high or the allowable battery
temperature is exceeded, the electronic control switches off
the power tool until the temperature is in the optimum tem-
perature range again.
Bosch Power Tools

Working Advice

" position, e. g. for
 Apply the power tool to the screw only when it is
switched off. Rotating tool inserts can slip off.
" symbol when un-
After longer periods of working at low speed, allow the ma-
chine to cool down by running it for approx. 3 minutes at max-
imum speed with no load.
For drilling in metal, use only perfectly sharpened HSS drill
bits (HSS=high-speed steel). The appropriate quality is guar-
anteed by the Bosch accessories program.
Before screwing larger, longer screws into hard materials, it is
advisable to predrill a pilot hole with the core diameter of the
thread to approx.

Maintenance and Service

Maintenance and Cleaning

 Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
 For safe and proper working, always keep the machine
and ventilation slots clean.
When the battery is no longer operative, please refer to an au-
thorised after-sales service agent for Bosch power tools.

After-sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts orders, please always
include the 10-digit article number given on the nameplate of
the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
English | 19
2
/ of the screw length.
3
1 609 92A 3T5 | (12.6.17)