Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

Liens rapides

External HiFD
Operating Instructions
Mode d'emploi
Bedienungsanleitung
Guía de instrucciones
Istruzioni per l'uso
SFD200S
-BP
© 1998 by Sony Corporation
Page 2
Page 24
Seite 44
Página 64
Pagina 84
3-864-865-21(2)
Drive
GB
FR
DE
ES
IT

Publicité

Table des Matières
loading

Sommaire des Matières pour Sony External HiFD Drive

  • Page 1 3-864-865-21(2) External HiFD Drive ™ Operating Instructions Page 2 Mode d’emploi Page 24 Bedienungsanleitung Seite 44 Guía de instrucciones Página 64 Istruzioni per l’uso Pagina 84 SFD200S © 1998 by Sony Corporation...
  • Page 2 The model number and the serial number are located on the bottom of the drive unit. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. SFD200S(-BP) Serial No.
  • Page 3 CONNECTION WITH THIS MANUAL, THE SOFTWARE OR OTHER INFORMATION CONTAINED HEREIN OR THE USE THEREOF. Sony Corporation reserves the right to make any modification to this manual or the information contained herein at any time without notice. The software described herein may also be governed by the terms of a separate user license agreement.
  • Page 4 Caution The mains plug on this equipment must be used to disconnect mains power. Please ensure that the socket outlet is installed near the equipment and shall be easily accessible. Précaution La prise principale de cet appareil doit être utilisée pour arrêter l’alimentation principale.
  • Page 5: Table Des Matières

    Contents Introduction ..............6 Features ................6 System requirements ............6 Precautions ..............6 Installation ................ 8 Package Contents ............8 Front/Rear of drive ............9 Hardware Installation ............ 11 Connecting to an AC outlet .......... 13 Software Installation ............. 14 Software Installation for DOS ........
  • Page 6: Introduction

    Introduction Introduction Features This HiFD (High-Capacity Floppy Disk) 3.5 inch floppy drive system offers the following: • 200 MB formatted storage capacity • Compatibility with 1.44 MB & 720 kB diskettes • High speed data access time (49 ms average) •...
  • Page 7: General Safety

    On Transportation • Save original packaging for later use. • Always remove diskette before moving unit. General Safety • If any solid object falls into drive, unplug it and before further operation, have qualified personnel inspect the unit. • Do not place foreign objects into DC IN 5V jack. On Power Sources •...
  • Page 8: Installation

    Installation Installation Package Contents Assure the following items are included in the package. Should anything be missing, contact local dealer or Sony. HiFD Drive Interface cable AC power cord AC power adaptor SA10-0515V Software disk 2 pcs HiFD blank disk (200 MB)
  • Page 9: Front/Rear Of Drive

    Front/Rear of drive Front View 200 MB Indicator Disk Slot BUSY Indicator POWER Indicator EJECT Button 1 Disk Slot Insert a HiFD or floppy disk here. 2 200 MB Indicator When a HiFD disk is present and the HiFD drive is on, this lamp lights in green.
  • Page 10 Installation Rear View Printer Port DC IN Jack PC Connector Connector 1 DC IN Jack Connect the supplied AC power adaptor here. 2 Printer Port Connector When using a printer, connect the printer cable (sold separately) here. 3 PC Connector Connect the supplied interface cable here.
  • Page 11: Hardware Installation

    Hardware Installation Locate the connection port. The parallel port is a 25-pin connector either vertically or horizontally positioned. It may be labelled “printer” or with printer symbol. Connect the printer cable. If a printer is connected, disconnect its cable and reconnect it to the HiFD’s port labelled “To Printer”.
  • Page 12 Installation Attach the supplied cable to other HiFD drive port. Attach other end (25-pins) of same interface cable to PC’s parallel port. Connect to either port Note Avoid tugging on cables, it may cause damage.
  • Page 13: Connecting To An Ac Outlet

    Connecting to an AC outlet Connect the drive to an AC outlet as illustrated. to AC outlet to DC IN 5V jack AC power cord (supplied) AC power adaptor (supplied) To switch unit off, disconnect AC power cord from outlet. Drive has no power switch on its own.
  • Page 14: Software Installation

    Installation Software Installation Sony’s HiFD driver software must be installed from supplied disk before the drive may be used. For Windows 3.x/95/98 and NT4.0 Install HiFD hardware and switch it on. Turn on PC. Insert supplied “Disk 1” in PC’s floppy drive.
  • Page 15 For Windows 3.x, click File Menu of the “Program Manager” and click Run. Type “:\setup.exe” and click OK. When the following screen appears, continue following the instructions displayed by installer.
  • Page 16: Software Installation For Dos

    Installation To Uninstall Click the task bar’s Start button, point to Programs, Sony HiFD and select UNINSTALL. To Uninstall under Windows 3.x In Sony HiFD Group, click on uninstall icon to remove drivers. Restart the PC after installing or uninstalling.
  • Page 17: Operation

    Operation Using the HiFD drive Follow these steps to connect and power up the system. The correct power-on sequence must be followed. Attach supplied 44-pin interface cable to drive. (See step 3 on page 12) Attach other end of cable to PC’s parallel port. (See step 4 on page 12) If using a printer, connect it to drive’s printer port.
  • Page 18: Inserting A Disk

    Operation Inserting a disk Insert a HiFD/Floppy disk into the drive. Before a floppy disk may be used, it must be formatted. Commercially available pre-formatted 200 MB HiFD or 1.44 MB DOS disks do not need to be reformatted. See Usable Floppy Disks on page 19 for compatibility details. Removing a disk Confirm BUSY indicator is not lit and press EJECT button.
  • Page 19: Write Protecting Data

    Write protecting data Floppy disks have a “write protect” tab to prevent accidentally erasing data. Illustrated below are its settings. Rear View of Floppy Disk Write-Enabled Write-Protected Rear View of HiFD Write-Enabled Write-Protected Usable floppy disks HiFD, 2HD and 2DD 3.5" disks are supported in this drive. Their formatted capacity and capabilities are listed below: Media Type Capabilities...
  • Page 20: The Utility Program

    The Utility Program The “Connect It” utility program is supplied with the HiFD drive. It is installed in the SONY HiFD Group or folder, selected in the Programs Menu, during installation. The following is based on Windows 95/98. DOS & Windows 3.x have no “Connect It”.
  • Page 21: Connecting The Hifd Drive

    Connecting the HiFD drive If PC was booted with HiFD drive unplugged, „Connect It“ may be used to cause Windows to recognize the drive. Run “Connect It”. Click the [Connect] tab, and click Connect button. [Connected] appears in the [Device] of [Properties] box. Disconnecting the HiFD drive To remove the HiFD drive without shutting down the PC, perform the same steps as above, except instead of selecting...
  • Page 22: Additional Information

    Never use any type of abrasive pad, scouring powder or solvent. Troubleshooting Should a problem or difficulty occur, please consult the Internet at http://www.sony-hifd.com or the following table before contacting Sony’s Hotline Support. Problem Cause/Solution...
  • Page 23: Service & Support Contacts In Europe

    For Central Europe (German or English) contact the hotline at: Tel. +49 (0) 2389 – 951047 or SONY-HOTLINE@SUPLIE.COM (Monday – Thursday, 8:00 am – 4:30 pm / Friday, 8:30 – 2:00 pm) For France or French-speaking countries (Switzerland, Benelux), please call: Tel.
  • Page 24 Table des Matières Table des matières Introduction ..............25 Caractéristiques ............. 25 Configuration requise ........... 25 Précautions ..............26 Installation ..............28 Contenu du coffret ............28 Avant/Arrière du lecteur ..........29 Installation matérielle ........... 31 Connexion à une prise de courant ......... 33 Installation logicielle ............
  • Page 25: Introduction

    Introduction Caractéristiques Ce lecteur de disquettes HiFD (High-Capacity Floppy Disk) 3,5 pouces présente les caractéristiques suivantes : • Capacité de stockage de 200 Mo de données formatées • Compatibilité avec les disquettes 1,44 Mo et 720 Ko • Temps d’accès aux données ultra rapide (49 ms en moyenne) •...
  • Page 26: Précautions

    Introduction Précautions Lors de l’installation Evitez les endroits exposées à une humidité ou une température élevée, aux vibrations mécaniques et en plein soleil. En cours de fonctionnement • Faites fonctionner le lecteur uniquement sur une surface solide et plane. • Ne déplacez pas le lecteur pendant son fonctionnement. Cela pourrait entraîner une défaillance.
  • Page 27: Au Niveau De L'unité Du Lecteur

    Au niveau de l‘unité du lecteur • Évitez les sources de chaleur (notamment les véhicules fermés exposés en plein soleil) et la lumière directe du soleil. Évitez l‘exposition à la poussière et au sable, à l‘humidité, à la pluie et aux chocs mécaniques. •...
  • Page 28: Installation

    Installation Installation Contenu du coffret Assurez-vous que les éléments suivants sont inclus dans le coffret. En cas d’élément manquant, prenez contact avec votre revendeur local ou avec Sony. Lecteur de HiFD Câble Interface Câble secteur Adaptateur secteur SA10-0515V 2 disquettes du logiciel...
  • Page 29: Avant/Arrière Du Lecteur

    Avant/Arrière du lecteur Face avant Témoin 200 MB Fente d’insertion Témoin d’activité du disque Témoin d’alimentation Boutton d’éjection 1 Fente d’insertion du disque Insérer une disquette HiFD ou floppy. 2 Témoin 200 MB Lorsque une disquette HiFD est présente et le lecteur sous tension ce voyant s’allume en vert.
  • Page 30 Installation Face arrière Connecteur Prise Jack Connecteur PC d’imprimante 1 Prise Jack Connecter l’adaptateur secteur fourni ici. 2 Connecteur d’imprimante Si une imprimante est utilisé connecter son câble (vendu séparément) ici. 3 Connecteur PC Connecter le câble interface fourni ici. Remarque Le lecteur peut être utilisé...
  • Page 31: Installation Matérielle

    Installation matérielle Localisez le port de connexion Le port parallèle est un connecteur à 25 broches positionné horizontalement ou verticalement. Il porte parfois l’indication “Printer” ou avec un logo d’imprimante. Connectez le câble de l‘imprimante. Si une imprimante est connectée, débranchez son câble et reconnectez- le sur le port portant l‘indication “To Printer”...
  • Page 32 Installation Reliez le câble fourni à l’autre port du lecteur de HiFD. Reliez l’autre extrémité (25 broches) du même câble d’interface au port parallèle du PC. Connecter à l’un ou à l’autre Remarque Évitez de tirer sur les câbles, cela pourrait les endommager.
  • Page 33: Connexion À Une Prise De Courant

    Connexion à une prise de courant Connectez le lecteur à une prise de courant comme indiqué sur l’illustration. Vers la prise secteur Vers la prise Cordon secleur jack 5V continu (fourni) Adaptateur secteur (fourni) Pour éteindre l’unité, débranchez le cordon d’alimentation de la prise.
  • Page 34: Installation Logicielle

    Installation Installation logicielle Vous devez installer le pilote HiFD de Sony à partir de la disquette fournie avant de pouvoir utiliser le lecteur.. Pour Windows 3.x/95/98 et Windows NT 4.0 Installez le matériel HiFD et mettez-le sous tension. Allumez le PC.
  • Page 35 Sous Windows 3.x, cliquez sur le menu Fichier du Gestionnaire de programmes, puis sur Exécuter. Tapez “A:\setup.exe” et cliquez sur OK. Lorsque l’écran ci-dessous apparaît, suivez les instructions affichées par le programme d’installation.
  • Page 36: Pour Désinstaller

    Dans la barre des tâches, cliquez sur Démarrer, pointez sur Programmes, Sony HiFD et sélectionnez UNINSTALL. Pour désinstaller sous Windows 3.x Dans le groupe Sony HiFD, cliquez sur l’icône de désinstallation pour supprimer les pilotes. Redémarrez le PC après installation ou désinstallation.
  • Page 37: Fonctionnement

    Fonctionnement Utilisation du lecteur de HiFD Procédez comme suit pour connecter et mettre sous tension le système. Il est très important de suivre correctement les étapes de mise sous tension. Reliez le câble d’interface à 44 broches fourni au lecteur. Reliez l’autre extrémité...
  • Page 38: Insertion D'une Disquette

    Fonctionnement Insertion d’une disquette Insérez une disquette HiFD/standard dans le lecteur. Disquette HiFD/Floppy Pour pouvoir être utilisée, une disquette doit être formatée. Des disquettes HiFD 200 Mo ou DOS 1,44 Mo préformatées sont disponibles dans le commerce et n’ont pas besoin d’être reformatées.
  • Page 39: Protection Des Données En Écriture

    Protection des données en écriture Les disquettes comportent un onglet de protection à l’écriture pour empêcher l’effacement accidentel de données. Les illustrations ci-dessous vous indiquent son fonctionnement. Vue arrière de la disquette Floppy Ecriture validée Protégé en ecriture Vue arrière du HiFD Protégé...
  • Page 40: L'utilitaire

    Exécution de “Connect It” Dans la barre des tâches, cliquez sur Démarrer, pointez sur Programmes, puis sur SONY HiFD et cliquez sur Connect It. Les propriétés du lecteur HiFD affichées varient selon qu’il était sous tension ou non lors du démarrage du PC.
  • Page 41: Connexion Du Lecteur De Hifd

    Connexion du lecteur de HiFD Si vous avez lancé le PC tandis que le lecteur de HiFD était débranché, vous pouvez utiliser “Connect It” pour faire reconnaître le lecteur par Windows. Exécutez “Connect It” Cliquez sur l’onglet [Connect], puis sur le bouton Connect. La mention [Connecté] s’affiche dans la zone [Propriétés] du périphérique.
  • Page 42: Informations Supplémentaires

    Dépannage En cas de problème ou de difficulté, pensez à consulter le site Internet à l’adresse http://www.sony-hifd.com ou le tableau suivant avant d’appeler le support technique de Sony. Problème Cause/Solution Les voyants Vérifier que l’adaptateur secteur est sous d’alimentation ou...
  • Page 43: Caractéristiques Techniques

    Au Royaume-Uni, composez le : Tél. 0870 900 8166 (Lundi – Vendredi, 8:45 à 17:00) Retrouvez et téléchargez ces informations et d’autres renseignements utiles sur le site Web Sony : http://www.sony-cp.com Caractéristiques techniques Prière de voir “Caractéristiques” en page 25 pour d’autres spécifications.
  • Page 44 Inhalt Inhalt Einleitung ............... 45 Eigenschaften ..............45 Systemanforderungen ........... 45 Vorsichtsmaßnahmen ........... 46 Installation ..............48 Packungsinhalt .............. 48 Vorder-/Rückseite des Laufwerks ........ 49 Hardware-Installation ........... 51 Anschluß an eine Netz-Steckdose ........ 53 Software-Installation ............. 54 DOS-Installation ............56 Bedienung ..............
  • Page 45: Einleitung

    Einleitung Eigenschaften Das HiFD (High Capacity Floppy Disk) 3,5-Zoll- Diskettenlaufwerk weist folgende Leistungsmerkmale auf: • 200 MB Speicherkapazität (formatiert) • Kompatibilität mit 1,44 MB- & 720 KB-Disketten • Hochgeschwindigkeits-Datenzugriff (im Durchschnitt 49 ms) • Paralleler Schnittstellenanschluß • Druckeranschluß • Max. Übertragungsgeschwindigkeit von 600 KB/s (mit EPP/ECP-Anschluß) Systemanforderungen •...
  • Page 46: Vorsichtsmaßnahmen

    Einleitung Vorsichtsmaßnahmen Installation Meiden Sie hohe Luftfeuchtigkeit oder Temperatur, mechanische Erschütterungen und direkte Sonneneinstrahlung. Betrieb • Stellen Sie das Laufwerk nur auf eine feste, ebene Fläche. • Das Laufwerk während des Betriebs nicht bewegen, da dies zu Störungen beim Lesen oder Schreiben führen kann. •...
  • Page 47 Laufwerk • Setzen Sie das Laufwerk weder Hitze oder direktem Sonnenlicht (z.B. in sonnenbeschienenen Autos) noch Staub, Sand, Feuchtigkeit, Regen oder mechanischen Erschütterungen aus. • Sollte das Gerät beim Radio- oder Fernsehempfang Störungen hervorrufen, stellen Sie es an einem anderen Ort auf. HiFD/Diskette Befolgen Sie bitte folgende Vorsichtsmaßnahmen, um die Daten auf der Diskette zu schützen:...
  • Page 48: Installation

    Installation Installation Packungsinhalt Vergewissern Sie sich, daß Ihre Packung vollständig ist. Ist dies nicht der Fall, wenden Sie sich an Ihren Händler vor Ort oder an Sony. HiFD-Laufwerk Schnittstellenkabel Netzkabel Netzadapter SA10-0515V Installationssoftware (2 Disketten) Leere HiFD-Diskette (200 MB) Kurzanleitung...
  • Page 49: Vorder-/Rückseite Des Laufwerks

    Vorder-/Rückseite des Laufwerks Vorderansicht 200 MB-Anzeige Disketten- In-Betrieb-Anzeige Einschub POWER-Anzeige EJECT-Taste 1 Disketten-Einschub Legen Sie die HiFD oder Floppy-Diskette hier ein. 2 200 MB-Anzeige Diese Anzeige leuchtet grün, wenn eine HiFD–Diskette eingelegt und das Laufwerk eingeschaltet ist. 3 In-Betrieb-Anzeige Diese Anzeige blinkt bernsteinfarben wenn das HiFD- Laufwerk arbeitet.
  • Page 50 Installation Rückansicht DC IN- Druckeranschluß PC-Anschluß Anschluß 1 DC IN-Anschluß Schließen Sie hier den mitgelieferten Netzadapter an. 2 Druckeranschluß Wenn Sie einen Drucker verwenden, schließen Sie das Druckerkabel (nicht im Lieferumfang) hier an. 3 PC-Anschluß Schließen Sie das mitgelieferte Schnittstellenkabel hier an. Hinweis Das Laufwerk kann in senkrechter oder waagerechter Lage verwendet werden.
  • Page 51: Hardware-Installation

    Hardware-Installation Suchen Sie den Anschluß. Der Parallelanschluß verfügt über 25 Pole und kann sowohl senkrecht als auch waagerecht angebracht sein. Er ist möglicherweise mit “Drucker” oder einem Druckersymbol beschriftet. Schließen Sie das Drucker-Kabel an. Ziehen Sie das Kabel des angeschlossenen Druckers heraus und schließen es an den mit “To Printer”...
  • Page 52 Installation Schließen Sie das vorgesehene Kabel an den anderen HiFD-Anschluß an. Schließen Sie das andere Ende (25 Pole) desselben Schnittstellenkabels an den Parallelanschluß des PCs an. Mit einem der Anschlüsse verbinden Hinweis Zerren Sie nicht an den Kabeln, da dadurch Schäden entstehen können.
  • Page 53: Anschluß An Eine Netz-Steckdose

    Anschluß an eine Netz-Steckdose Schließen Sie das Laufwerk an eine Netz-Steckdose an (siehe Abbildung). zur Steckdose Netzkabel DC IN 5V-Anschluß (im Lieferumfang) Netzadapter (im Lieferumfang) Die Stromzufuhr des Laufwerks schalten Sie durch Ziehen des Netzsteckers aus, da das Laufwerk über keinen eigenen Netzschalter verfügt.
  • Page 54: Software-Installation

    Installation Software-Installation Vor Gebrauch des Laufwerks muß die HiFD- Treibersoftware von Sony installiert werden. Für Windows 3.x/95/98 und NT4.0 Installieren Sie das HiFD-Laufwerk und schalten Sie es ein. Schalten Sie den PC ein. Legen Sie “Diskette 1” in das Diskettenlaufwerk des PCs ein.
  • Page 55 Für Windows 3.x, klicken Sie im “Programm-Manager” auf das Menü Datei und wählen dann Ausführen. Geben Sie “A:\setup.exe” ein und klicken dann auf OK. Bei der Anzeige dieses Bildschirms folgen Sie weiterhin den Anweisungen des Installationsprogramms.
  • Page 56: Dos-Installation

    Installation Deinstallieren Zum Deinstallieren klicken Sie auf der Task-Leiste auf Start, dann auf Programme, Sony HiFD, und wählen Sie DEINSTALLATION. Deinstallieren unter Windows 3.x Zur Deinstallation der Treiber unter Windows 3.x klicken Sie in der Sony HiFD-Gruppe auf das Deinstallationssymbol.
  • Page 57: Bedienung

    Bedienung Gebrauch des HiFD-Laufwerks Befolgen Sie die folgenden Schritte, um das Gerät einzuschalten. Die Reihenfolge muß beachtet werden. Schließen Sie das 44-Pol-Schnittstellenkabel an das Laufwerk an. Schließen Sie das andere Ende des Kabels an den Parallelanschluß des PCs an. Für den Drucker ist der Druckeranschluß zu benutzen. Stecken Sie das Stromanschlußkabel in den dafür vorgesehenen Ausgang.
  • Page 58: Einlegen Einer Diskette

    Bedienung Einlegen einer Diskette Legen Sie eine HiFD-Diskette in das Laufwerk. HiFD/Floppy-Diskette Die Diskette muß zunächst formatiert werden. Im Handel erhältliche vorformatierte 200 MB-HiFD- oder 1,44 MB-DOS- Disketten müssen nicht nochmals formatiert werden. Genauere Informationen zur Kompatibilität finden Sie unter “Verwendbare Disketten”...
  • Page 59: Schreibschutz Von Disketten

    Schreibschutz von Disketten Damit Daten nicht versehentlich gelöscht werden, haben Disketten einen “Schreibschutz”, dessen Einstellungen unten abgebildet sind. Rückseite einer Floppy-Diskette Nicht Schreibgeschützt schreibgeschützt Rückseite einer HiFD-Diskette Nicht Schreibgeschützt schreibgeschützt Verwendbare Disketten In diesem Laufwerk können HiFD, 2HD and 2DD 3,5-Zoll- Disketten mit folgenden Eigenschaften benutzt werden: Disketten-Typ Eigenschaften...
  • Page 60: Dienstprogramm

    Dienstprogramm Dienstprogramm Das Dienstprogramm “Connect It” ist im Lieferumfang des HiFD-Lauf-werks enthalten. Es wird in der SONY HiFD- Programmgruppe oder in dem während der Installation ausgewählten Verzeichnis des “Programme”–Menüs installiert. Der folgenden Beschreibung liegt Windows 95/98 zugrunde. DOS & Windows 3.x verfügen über kein “Connect It”- Dienstprogramm.
  • Page 61: Verbindung Zum Hifd-Laufwerk Herstellen

    Verbindung zum HiFD-Laufwerk herstellen War das HiFD-Laufwerk beim Booten des PCs nicht eingeschaltet, kann Windows das Laufwerk mit Hilfe von “Connect It” erkennen. Führen Sie “Connect It” aus. Klicken Sie auf das [Connect]-Register und anschließend Connect. Im Abschnitt [Device] des Felds [Properties] erscheint [Connected].
  • Page 62: Zusätzliche Information

    Material, Scheuer- oder Lösungsmittel. Fehlerbehebung Sollten Probleme auftreten, schauen Sie erst im Internet unter http://www.sony-hifd.com nach, oder gehen Sie folgende Liste durch, bevor Sie sich an die Sony-Hotline wenden. Problem Ursache/Fehlerbehebung Überprüfen Sie, ob der Netzadapter Die POWER oder BUSY richtig angeschlossen ist.
  • Page 63: Technische Daten

    Für Frankreich oder französchsprachige Länder (Schweiz, Benelux) wählen Sie bitte: Tel. +33 (0)1 55 87 08 66 E-mail: HT-SONY@nati.fr (Montag – Freitag, 9.00 bis 18.00 Uhr) Für DK, N, SW & FIN wählen Sie bitte: Tel. +47 (0) 6281 8666 (Montag –...
  • Page 64 Índice Índice Introducción ..............65 Características ............... 65 Requerimientos del sistema .......... 65 Precauciones ..............66 Instalación ..............68 Contenido del embalaje ..........68 Panel frontal y posterior ..........69 Instalación del hardware ..........71 Conexión a la red ............73 Instalación del software ..........
  • Page 65: Introducción

    Introducción Características Esta unidad de disquete HiFD (disquete de alta capacidad) de 3,5 pulgadas ofrece las siguientes características: • Capacidad de almacenamiento de 200 MB • Compatibilidad con disquetes de 1,44 MB y de 720 kB • Tiempo de acceso de alta velocidad (49 ms de media) •...
  • Page 66: Precauciones

    Introducción Precauciones Durante la instalación Evite zonas con humedad o temperaturas elevadas, vibraciones mecánicas o luz del sol directa. Durante el funcionamiento • Utilice la unidad solamente en una superficie estable y plana. • No mueva la unidad mientras esté funcionando, pueden producirse errores.
  • Page 67 Manejo del disquete/HiFD Siga las siguientes instrucciones para proteger el disquete y los datos: • Evite imanes y campos magnéticos (TV, radio). • Evite fuentes de calor y la exposición directa al sol. • No tocar nunca la superficie del disquete (no abrir la ventanilla con la mano), la suciedad o las marcas en la superficie pueden dejar los datos ilegibles y el disquete inservible.
  • Page 68: Instalación

    Instalación Contenido del embalaje Compruebe que los siguientes elementos están incluidos en el embalaje. Si faltase alguno, póngase en contacto con el distribuidor o con Sony. Unidad HiFD Cable de Interface Cable de red AC Adaptador de red AC SA10-0515V...
  • Page 69: Panel Frontal Y Posterior

    Panel frontal y posterior Vista frontal Indicador de 200 MB Indicador de Disquetera ACTIVIDAD Indicador de ENCENDIDO Botón de EXPULSION 1 Disquetera Inserte un disquete o un HiFD 2 Indicador de 200 MB Cuando un disquete de HiFD esté introducido y la unidad HiFD esté...
  • Page 70 Instalación Vista posterior Conector del puerto de Conector de PC Clavija DC IN impresora 1 Clavija DC IN Conecte el adaptador de red AC suministrado aquí. 2 Conector del puerto de impresora Cuando use una impresora, conecte su cable (no suministrado) aquí.
  • Page 71: Instalación Del Hardware

    Instalación del hardware Localice el puerto de conexión. El puerto paralelo, es un conector de 25 contactos, en orientación vertical u horizontal. Puede que esté marcado “impresora” o con símbolo de impresora. Conecte el cable de la impresora Si hubiera una impresora conectada, desconecte el cable y conéctelo al puerto de la unidad HiFD con la indicación “To Printer”...
  • Page 72 Instalación Conecte el cable que se suministra al otro puerto de la unidad HiFD. Conecte el otro extremo del mismo cable (25 contactos) al puerto paralelo del PC. Conectelo a otro puerto Nota Evite tirar de los cables, podría causar daños.
  • Page 73: Conexión A La Red

    Conexión a la red Enchufe la unidad a la red de la forma en que se indica. Al enchufe de AC Cable de red AC A la clavija DC IN 5V (suministrado) Adaptador de red AC (suministrado) Para apagar la unidad, desenchúfelo de la red. La unidad no tiene interruptor propio.
  • Page 74: Instalación Del Software

    Instalación Instalación del software Es necesario instalar desde el disquete el software de controlador para la unidad HiFD de Sony antes de poder usar la unidad. Para Windows 3.x/95/98 y NT4.0 Instale el hardware HiFD y encienda la unidad. Encienda el PC.
  • Page 75 Para Windows 3.x, haga clic en el menú Archivos en el “Administrador de Programas” y después sobre Ejecutar. Teclee “A:\setup.exe” y confirme con el botón Aceptar. Cuando aparezca la pantalla siguiente, siga las instrucciones que muestra el programa de instalación.
  • Page 76: Instalación Bajo Dos

    Programas, Sony HiFD y elija la opción UNINSTALL (desinstalar). Para desinstalar bajo Windows 3.x En el grupo Sony HiFD, haga clic en el icono de desinstalación para quitar los controladores. Reinicialice el PC después de instalar o desinstalar.
  • Page 77: Funcionamiento

    Funcionamiento Utilización de la unidad HiFD Siga estas instrucciones para conectar y encender el sistema. Hay que realizar las operaciones en el orden indicado. Conecte el cable de interface de 44 contactos a la unidad. Conecte el otro extremo del cable al puerto paralelo del Si se usa una impresora, conéctela al puerto de impresora de la unidad.
  • Page 78: Insertar Un Disquete

    Funcionamiento Insertar un disquete Inserte un disquete o HiFD en la unidad. Disquete HiFD/Floppy Antes de que se pueda usar un disquete, es necesario formatearlo. De usarse discos HiFD de 200 MB o disquetes de 1,44 MB preformateados bajo DOS, no será necesario formatearlo de nuevo.
  • Page 79: Protección De Los Datos Contra La Escritura

    Protección de los datos contra la escritura Los disquetes tienen una pestaña de “protección” contra la escritura para evitar que se puedan perder datos accidentalmente. Éstas son sus posiciones. Vista posterior del disquete Escritura Protección permitida contra escritura Vista posterior del HiFD Escritura Protección permitida...
  • Page 80: El Programa De Utilidades

    El programa de utilidades “Connect It” viene con la unidad HiFD. Se instala bajo el grupo o carpeta SONY HiFD, seleccionado en el menú de Programas durante la instalación. La siguiente descripción está basada en Windows 95/98. Connect It no está...
  • Page 81: Conexión De La Unidad Hifd

    Conexión de la unidad HiFD Si se arrancó el PC con la unidad HiFD desenchufada, se puede usar “Connect It” para hacer que Windows reconozca la unidad. Ejecute “Connect It” Haga clic en la ficha [Connect] (Conectar), y en el botón Connect.
  • Page 82: Información Adicional

    Para Europa central (alemán o inglés) marque el número: Tel. +49 (0) 2389 – 951047 o SONY- HOTLINE@SUPLIE.COM (Lunes – jueves, de 08.00 a 16.30 / Viernes de 08.30 a 14.00)
  • Page 83: Especificaciones

    Para Francia o paises de habla francesa (Suiza, Benelux), por favor llame: Tel. +33 (0)1 55 87 08 66 E-mail: HT-SONY@nati.fr (Lunes – viernes, de 09.00 a 18.00) Para DK, N, SW y FIN, marque: Tel. +47 (0) 6281 8666 (Lunes –...
  • Page 84 Sommario Sommario Introduzione ..............85 Caratteristiche ............... 85 Requisiti minimi di sistema .......... 85 Precauzioni ..............86 Installazione ..............88 Contenuto della confezione .......... 88 Vista anteriore e posteriore del drive ......89 Installazione hardware ..........91 Collegamento a una presa c.a........93 Installazione software ...........
  • Page 85: Introduzione

    Introduzione Caratteristiche Questo drive HiFD (High-Capacity Floppy Disk, floppy disk ad alta capacità) per floppy disk da 3,5 pollici presenta le seguenti caratteristiche: • Capacità di memorizzazione fino a 200 MB (disco formattato). • Compatibilità con i dischetti da 1,44 MB e da 720 KB. •...
  • Page 86: Precauzioni

    Introducción Precauzioni Installazione Evitare di installare il drive in luoghi soggetti a temperature o tassi di umidità elevati, a vibrazioni meccaniche e alla luce diretta del sole. Funzionamento • Collocare il drive esclusivamente su una superficie piana e resistente. • Non spostare il drive durante il funzionamento: potrebbero verificarsi errori in lettura o scrittura.
  • Page 87 • Non lasciare i dischetti nel drive, riporli nella custodia. Attenzione L’impiego dei dischetti di pulizia usati per i normali floppy drive rischia di danneggiare questo drive. Non inserire mai tali tipi di dischetti nel drive HiFD Sony.
  • Page 88: Installazione

    Installazione Installazione Contenuto della confezione Accertarsi che la confezione contenga quanto illustrato di seguito. Se dovesse mancare qualcosa, contattare il proprio rivenditore locale o la Sony. Drive HiFD Cavo dati Cavo di alimentazione Adattatore di rete SA10-0515V Driver software (2 dischi)
  • Page 89: Vista Anteriore E Posteriore Del Drive

    Vista anteriore e posteriore del drive Vista frontale LED HiFD Vano di LED lettura/scrittura inserimento LED di alimentazione Pulsante di espulsione 1 Vano di inserimento Inserire qui un disco HiFD o un floppy. 2 LED HiFD Quando il drive è acceso ed è inserito un disco HiFD il LED è...
  • Page 90 Installazione Vista posteriore Connettore Connettore di Connettore della della porta alimentazione porta PC stampante 1 Connettore di alimentazione Collegare qui l’adattatore di rete. 2 Connettore della porta stampante Per l’utilizzo di una stampante, collegarne qui il relativo cavo (non fornito). 3 Connettore della porta PC Collegare qui il cavo dati fornito nella confezione del drive.
  • Page 91: Installazione Hardware

    Installazione hardware Individuare la porta di collegamento (parallela). La porta parallela è un connettore a 25 pin disposto verticalmente od orizzontalmente sul retro del PC. Può essere identificata come “stampante” o con simbolo della stampante. Collegare il cavo dati. Se è già collegata una stampante, scollegarne il cavo e ricollegarlo alla porta dell’HiFD contrassegnata “To Printer”...
  • Page 92 Installazione Collegare il cavo dati in dotazione all’altra porta del drive HiFD. Collegare l’altra estremità (a 25 pin) dello stesso cavo dati alla porta parallela del PC. Collegare ad entrambe le porte Nota Evitare di tirare eccessivamente i cavi per non danneggiarli.
  • Page 93: Collegamento A Una Presa C.a

    Collegamento a una presa c.a. Collegare il drive a una presa c.a. come illustrato nella figura. Alla presa c.a. Al connettore DC IN 5V Cavo di alimentazione (fornito nella confezione) Adattatore di rete (fornito nella confezione) Per spegnere il drive, disinserire il cavo di alimentazione c.a. dalla presa.
  • Page 94: Installazione Software

    Installazione Installazione software Prima di usare il drive, occorre installare il driver software HiFD Sony contenuto nei dischi forniti nella confezione. Per Windows 3.x/95/98 e NT 4.0 Installare l’hardware HiFD e accendere il drive. Accendere il PC e attendere il caricamento di Windows.
  • Page 95 Per Windows 3.x, fare clic sul menu File del Program Manager, quindi selezionare Esegui. Digitare “A:\setup.exe” e fare clic su OK. Quando compare la seguente schermata, continuare a seguire le istruzioni visualizzate dal programma di installazione.
  • Page 96: Installazione Dos

    Fare clic sul pulsante Avvio/Start nella barra delle applicazioni, selezionare Programmi, Sony HiFD e quindi UNINSTALL. Per disinstallare in Windows 3.x Nel gruppo Sony HiFD fare clic sull’icona di disinstallazione per rimuovere i driver. Dopo l’installazione o la disinstallazione, riavviare il PC.
  • Page 97: Funzionamento

    HiFD. Collegare il cavo di alimentazione c.a. a una presa a parete. Accendere il PC. Per un corretto funzionamento del drive, occorre prima installare il driver software Sony HiFD. Nota Per fare in modo che Windows riconosca il drive HiFD,...
  • Page 98: Inserimento Di Un Disco

    Funzionamento Inserimento di un disco Inserire un floppy disk/HiFD nel drive. Disco HiFD/Floppy disk Prima di usare un floppy disk, occorre formattarlo. I dischi preformattati da 200 MB HiFD o da 1,44 MB DOS reperibili in commercio non devono essere formattati di nuovo. Per i dettagli sulla compatibilità, vedere Floppy disk utilizzabili a pagina 99.
  • Page 99: Protezione Dei Dati Dalla Scrittura

    Protezione dei dati dalla scrittura I floppy disk sono provvisti di una linguetta di protezione dalla scrittura che impedisce la cancellazione accidentale dei dati. La figura illustra le impostazioni della linguetta. Vista posteriore di un Floppy Disk Scrittura Scrittura abilitata disabilitata Vista posteriore di un disco HiFD Scrittura...
  • Page 100: Il Programma "Connect It

    “Connect It” è un programma fornito con il drive HiFD e, durante l’installazione, viene collocato nel gruppo o nella cartella SONY HiFD, selezionabile dal menu Programmi. Le istruzioni elencate di seguito si basano sull’uso di Windows 95/ 98. Le versioni per DOS e Windows 3.x non sono dotate di Connect It.
  • Page 101: Collegamento Del Drive Hifd

    Collegamento del drive HiFD Se il PC è stato avviato prima di accendere il drive HiFD, si può usare Connect It in modo che Windows riconosca il drive. Eseguire Connect It. Fare clic sulla scheda [Connect], poi sul pulsante Connect. Nel campo [Device] del riquadro [Properties] viene visualizzato [Connected].
  • Page 102: Informazioni Supplementari

    Per l’Europa centrale (tedesco o inglese), contattare la hotline al seguente numero: Tel. +49 (0) 2389 – 951047 o SONY-HOTLINE@SUPLIE.COM (lunedì – giovedì, dalle 8:00 alle 16:30 / venerdì, dalle 8:30 alle 14:00 GMT)
  • Page 103: Specifiche

    Per la Francia o paesi di lingua francese (Svizzera, Benelux), comporre il seguente numero: Tel. +33 (0)1 55 87 08 66 E-mail: HT-SONY@nati.fr (lunedì-venerdì, dalle 9:00 alle 18:00) Per Danimarca, Norvegia, Svezia e Finlandia, chiamare: Tel. +47 (0) 6281 8666 (lunedì-venerdì, dalle 8:30 alle 16:00 CET) Nel Regno Unito, chiamare: Tel.
  • Page 104 Specifications Sony Corporation Printed in Japan...

Ce manuel est également adapté pour:

Sfd200s

Table des Matières