Publicité
Les langues disponibles
Les langues disponibles
English
WARNING:
To avoid the risk of fire, explosion, or
electric shock, this product should be
installed, inspected, and maintained by
a qualified electrician in accordance
with all applicable electrical rules and
regulations.
Safety Instruction:
To avoid electric shock:
Be certain electrical power is OFF
before and during installation and
maintenance.
Make sure the supply voltage is the
same
as
the
rated
voltage.
The technical data indicated on
the LED luminaires are to be
observed.
Changes
of
the
modifications to the LED luminaire
are not permitted.
Observe
the
national/regional
electrical
safety
regulations during installation.
The LEDs of this luminaire are not
replaceable; when the LEDs reach
their
end
of
life,
luminaire shall be replaced.
Equipment Application
This product can be used inside to illuminate
areas in an industrial location.
Mounting the Luminaire
This product can be mounted via hook, loop,
or chain mount.
WARNING: Please ensure the application
structure can handle the weight of the
luminaire. Dialight is not responsible for any
damages to the application structure or the
luminaire when mounted improperly.
Installation
Ensure that the mains voltage supply is
disconnected
before
connecting
luminaire.
Install
the
accordance
with
the
instructions as well as any other applicable
electric codes.
Always transport and store the equipment in
its original packaging and keep in a dry
location. When unpacking check for any
cracks or damage in the housing or lens. If in
doubt, do not install.
Page 3 of 24
Reliant™ EMEA/APAC High Bay
Technical Data:
Locations:
RR******(D/H/J/K)***** IP-66 Applications
RR******(E/F)*****
UL 1598 Variations (RRU***********):
Suitable for Damp Locations
Convient aux Emplacements Humides
Temperature Range:
-40°C to +55°C [-25°F to +131°F]
Rated Input Voltage:
RR****(2/3)*(D/H/J/K)*****
luminaire
RR****(2/3)*(E/F)*****
Weight:
RR***********N
design
and
Dimensions:
See Technical Diagrams
rules
and
Conductor Range:
0.5-4 mm² [20-12 AWG]
the
whole
NOTE: The cabling used must be suitable for
the
site
requirements.
When assembling the cable entries for the
mains
connection,
manufacturer's specifications for the glands
used. Unused cable entries must be closed
and sealed by a certified blanking plug.
NOTE: The addition of cable glands, dust
caps, electrical plugs, or occupancy sensors
may change the IP rating of this luminaire.
WARNING: Do not over tighten as the
protection rating may be compromised.
Always refer to the gland manufacturer's
data for torque settings.
the
Opening/Closing the Luminaire
equipment
in
To open the luminaire, the lid can be
manufacturer's
removed via the snap features built into it.
There are 3 points of contact that snap the lid
of the luminaire closed.
NOTE: The lid is secured to the wiring box via
a lanyard; eliminating risk of dropping the
lid upon removal.
IP-65 Applications
100-277 VAC
50/60 Hz
220-240 VAC
50 Hz
9.3 kg [20.5 lbs.]
application
and/or
the
always
observe the
Dialight, 1501 Route 34 South, Farmingdale, NJ, USA 07727
Tel: +1 732 919 3119 Fax: +1 732 751 5778
Technical Data:
Power Consumption:
RR****(2/3)A*****N
RR****(2/3)B*****N
RR****(2/3)C*****N
RR****(2/3)E*****N
RR****(2/3)G*****N
RR****(2/3)J*****N
Snap Features
site
NOTE: The lid of the luminaire should be
oriented as shown above. The Dialight logo
should be aligned with the mounting bracket.
Electrical Connections
The terminal block is suitable for multi-
stranded or single core wires. The parameters
can be found in Technical Data.
When
terminating
the
insulation of the conductors shall reach up to
the terminal block. The conductor itself shall
not be damaged.
When connecting wires; push down at the
'cross point', insert wire, and release. Ensure
all the conductors have been securely
retained.
75 W
100 W
120 W
167 W
198 W
242 W
conductors,
the
9100127385599 REV A
www.dialight.com
Publicité
