BH FITNESS G-6446N Instructions De Montage Et Utilisation page 15

ASSEMBLY INSTRUCTIONS
Take the unit out of the box and place it on the
floor as shown in Figure 0.
The assistance of a second person is advisable
for the assembly work. Make sure that all of the
pieces are there:
(B) Main structure;
Safety key; (i) Bottle of lubricant.
Follow the instructions
assemble:
1.-
First loosen the two top holding knobs (K)
by two turns, anticlockwise, Fig. 1, next take
hold of the handrails (G and H) and lift them in
the direction of the arrow, as shown in Fig. 2,
until you hear the top holding knobs (K) click
into position.
2.-
Now loosen off the bottom holding knobs by
two turns (L) Fig. 3.
Holding the handrails (G and H), lift the focus
bars in the direction of the arrow, see Fig. 4,
until you hear the bottom holding knobs (L) click
into position.
NOTE: Make sure that you hear the top holding
knobs click into the handrails and the bottom
knobs click into the focus bars before you let go
of the handrails.
3.-
Once you have completed the above,
tighten the top knobs (K) securely, Fig. 5, by
turning them clockwise and the bottom knobs
(L) Fig. 5, by turning it clockwise.
ATTENTION: Cylinder (Q) Fig (6) is factory set
to high pressure so it must not be knocked. If it
is knocked this may damage it and impair the
operation of the treadmill
FOLDING YOUR UNIT
To fold your unit, stop the machine completely
and unplug it from the wall socket. Lift the base of
the machine, pull pin (S), as shown in Fig. (6)
until it clips into the frame. You can now release
the machine.
UNFOLDING YOUR UNIT
To unfold the machine carry out the procedure
in reverse, i.e. hold the machine with one hand
and use the other hand to pull pin (S) in the
direction of the arrow, Fig. (6) and lower the
machine gently onto the floor. and lower the
machine gently onto the floor. When folding or
unfolding the treadmill make sure that there are
(f) Allen key 6 mm; (g)
step by step
no children about or obstacles that might hinder
the folding motion.
MOVEMENT & STORAGE
The unit is equipped with wheels (P), Fig. (7)
to make it easier to move. Make sure that the
mains cable is unplugged from the wall socket.
If you wish to move the treadmill, the first thing
to do is to fold it up, place your hands on the
handrails (G & H) and tilt the treadmill, Fig (7),
to so that the wheels (P) rest on the floor.
To prevent accidents DO NOT move the treadmill
across uneven floors.
ELEVATION SYSTEM
The machine has 3 levels of inclination.
Carry out the following steps to use the different
positions: Make sure that the unit has stopped
completely. Fold the unit as shown in Fig. (8),
pull the crossbar (M) backwards in the direction of
the arrow and turn it to position it in the slot for the
level that you wish to use.
MAINTENANCE
Use the bottle of lubricant (i) to lubricate the
inside of the belt in order to keep your unit in top
condition and to ensure that friction between the
belt and the board is kept to a minimum (due to
different running styles, always apply more
lubrication to the area where you place your feet
during the exercise) It is advisable to lubricate
the base of the belt every 3-12 months,
depending on how often it is used.
If the belt starts to slip after lubrication, then
check the tension of the belt. To tension the
belt, take the 6 mm Allen key (f) and with the
machine set to 4 km/h turn screws (R & L) one
turn in a clockwise direction.
Operating
speed
1~6 km
6~12 km
12~16 km
ADJUSTING THE BELT
If your unit is not seated evenly on the four
contact points, this may cause the belt (X) to
shift sideways. Rigorous quality control adjusts
and checks the running belt. However, due to
weight differences and individual styles of
running, the belt may be prone to shift
sideways.
If the belt does shift to the left or right, stop the
machine.
15
.
Recommended lubrication
period
1 year
6 months
3 months