Gardena THS 42/18V P4A Mode D'emploi page 12

2. ASSEMBLY
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Remove the battery and slide the protective cover over the
blade before you assemble the product.
To assemble the telescopic handle [ Fig. A1 / A2 ]:
1. Slide the telescopic tube (2)
stop position. The two markings
2. Tighten the grey nut (3) .
3. OPERATION
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Wait for the blade to stop, remove the battery and slide the
protective cover over the blade before you adjust or transport
the product.
To charge the battery [ Fig. O1 / O2 / O3 ]:
CAUTION!
v Note the mains voltage! The voltage of the power source must
match the voltage specified on the rating plate of the charger.
For the GARDENA Battery Hedge Trimmer Art. 14732-55 there is no
battery and no charger in the scope of delivery.
Thanks to the intelligent charging process, the charge condition of the
battery is automatically detected and then charged up with the optimal
charge current depending on battery temperature and voltage.
In this way, the battery is treated with care and remains permanently fully
charged when it is stored in the charger.
1. Push the locking button (A)
(D)
holder .
2. Connect the battery charger
(C)
3. Slide the battery charger
When the battery charge indicator
the battery is being charged.
When the battery charge indicator
permanently green the battery is completely charged
(Charging time, see 7. TECHNICAL DATA).
4. Examine the charge status regularly while you charge.
5. When the battery (B) is completely charged, you can disconnect the
(B)
battery from the charger
Meaning of the indication elements:
Indication on the charger:
Flashing of the battery The charging procedure is indicated by flashing of the battery charge
(Lc) (Lc)
charge indicator indicator
Note: The charging procedure is only possible when the battery
temperature is within the allowable charging temperature range,
see 7. TECHNICAL DATA.
Continuous lighting Continuous lighting of the battery charge indicator
of the battery the battery is fully charged or that the temperature of the battery is
(Lc)
charge indicator not within the allowable charging temperature range and can therefore
not be charged.
When the battery is not inserted, continuous lighting of the battery
charge indicator
socket outlet and that the battery charger is ready for operation.
Battery charge status indication
After starting the product, the battery charge status indication
is displayed for 5 seconds.
Battery charge status
67 – 100 % charged
34 – 66 % charged
11 – 33 % charged
0 – 10 % charged
If the LED (L1) flashes green, the battery must be charged.
(Wp)
If the error LED is illuminated or flashing, see 6. TROUBLESHOOTING.
12
14732-20.960.01.indd 12
into the motor unit (1) until you reach the
(M) must be opposite from each other.
and remove the battery (B) from the battery
(C) into a mains socket.
(B)
onto the battery .
(Lc) at the charger flashes green
(Lc) at the charger illuminates
(C)
.
.
(Lc)
indicates that
(Lc)
indicates that the mains plug is inserted in the
(P) on the product [ Fig. O4 / O12 ]:
Battery charge status indication
(L1) , (L2) and (L3) illuminate green
(L1) and (L2) illuminate green
(L1)
illuminates green
(L1) flashes green
Work positions:
The hedge trimmer can be operated in 4 positions.
Side trimming:
[ Fig. O5 ]
Vertical trimming at high level:
[ Fig. O6 ]
Horizontal trimming at high level:
[ Fig. O7 ]
Low trimming:
[ Fig. O8 ]
To tilt the motor unit [ Fig. O9 ]:
For trimming at high and low level, the motor unit
an angle of 75° to – 60° in 15° increments.
1. Keep both orange buttons
the desired direction.
2. Release both orange buttons
To extend the telescopic tube [ Fig. O10 ]:
For cutting at high and low heights, the telescopic pipe
continuously extended by up to 50 cm.
1. Loosen the orange nut
2. Extend the telescopic tube
3. Tighten the orange nut
To start the hedge trimmer [ Fig. O1 /O11 /O12 ]:
DANGER! Risk of injury!
Risk of injury if the product does not stop when you
release the start lever.
v Do not bypass the safety devices or switches. For example do
not attach the start lever to the handle.
To start:
The product is provided with a two-switch safety device (start
lever with starting lockout) to prevent the product from being
turned on by accident.
(B)
1. Put the battery into the battery holder
2. Remove the protective cover from the blade.
3. Hold the hedge trimmer with one hand on the insulated gripping
surface on the telescopic tube
(6)
handle .
4. Slide the starting lockout
The hedge trimmer starts and the battery charge status indication
is displayed for 5 seconds.
5. Release the starting lockout
To stop:
1. Release the start lever (8)
The hedge trimmer stops.
2. Slide the protective cover over the blade.
3. Push the locking button
battery holder (D) .
4. MAINTENANCE
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Wait for the blade to stop, remove the battery and slide
the protective cover over the blade before you maintain
the product.
(P)
To clean the Hedge Trimmer:
DANGER! Risk of injury!
Risk of injury and risk of damage to the product.
v Do not clean the product with water or with a water jet
(in particular high-pressure water jet).
v Do not clean with chemicals including petrol or solvents.
Some can destroy critical plastic parts.
The airflow slots must always be clean.
Telescopic tube retracted
Telescopic tube extended
Motor unit tilted by 75°,
telescopic tube extended
Motor unit tilted by – 60°,
telescopic tube extended
(1) can be tilted at
(4) pushed and tilt the motor unit
(4) and let the motor unit (1) engage.
(2)
can be
(5)
.
(2) to the desired length.
(5)
again.
(D)
until it audibly engages.
(2) and with the other hand on the
(7) forward and pull the start lever
(7) .
.
(A) (B)
and remove the battery from the
(1) in
(8) .
(P)
11.09.20 12:11