Milwaukee 5615-20 Manuel De L'utilisateur page 9

Holding the Tool
These tools should be held using both hands at all
times for maximum control.
For Bodygrip bases:
®
You can hold this
tool using the body
grip and ball handle
or both ball handles.
The body grip fea-
tures an adjustable
strap, which can be
attached in two dif-
ferent positions for
maximum control
and comfort.
One handle on these
bases may be ad-
justed to three dif-
ferent positions for
maximum control
and comfort.
For D-Handle base:
Grip the D-handle
with one hand and
place the other on
the ball handle.
One handle on these
bases may be ad-
justed to three dif-
ferent positions for
maximum control
and comfort.
For Plunge and Production bases:
Warning
injury, NEVER use the Plunge Base Router
in a router table.
Warning
injury, wear safety goggles or glasses with
side shields.
To reduce the risk of injury, keep hands, body
and cord away from the bit and all moving
parts.
Before plugging the tool into a power outlet,
make sure the on/off switch is in the "O"
position.
Starting and Stop-
ping Router Motor
For Cat. No. 5615-
2 0 , 5 6 1 6 - 2 0
and 5625-20:
1. To start the motor,
place the router
so the bit is away
from you and not
in contact with the
workpiece. Grasp
the tool firmly and
push the On/Off
switch to the "I"
position.
Fig. 14
Alternate
strap
positions
Fig. 15
Alternate
handle
positions
To reduce the risk of
To reduce the risk of
Fig. 16
2. To stop the motor, place the router so the bit is
away from you and push the On/Off switch to the
"O" position. Hold the tool until the bit stops turning.
For Cat. No. 5619-20:
1. Push the On/Off switch to the "I" position.
2. To start the motor, place the router so the bit is
away from you and not in contact with the work-
piece. Grasp the tool firmly and pull the trigger.
3. To stop the motor, release the trigger.
Locking the D-handle Base Trigger
The lock button
holds the trigger in
the ON position for
continuous use.
1. To l o c k t h e
trigger, hold in
the lock button
while pulling the
trigger. Release
the trigger.
2. To unlock the
trigger, pull the
trigger and re-
lease. The lock
button will pop
out.
NOTE: D-handle base does not fit Cat.No.5625-20.
Electronic Overload Protection
(For Cat. No. 5616-20 and 5625-20 only)
These tools are equipped with an electronic over-
load protection feature.
If the motor shuts off during use, remove the bit
from the workpiece and push the On/Off switch
to the "O" position for three (3) seconds. This will
reset the electronics in the tool. The tool can then
be restarted.
Using the Variable Speed Dial
(For Cat. No. 5616-20 and 5625-20 only)
The variable speed dial allows the user to adjust
the rotating speed (RPM) of the tool.
Variable speed dial settings range from numbers (7)
seven through (1) one. Higher numbers correspond
to higher speeds and lower number correspond to
lower speeds.
To change the speed, set the variable speed control
dial to the desired number.Soft Start
(For Cat. No. 5616-20 and 5625-20 only)
The Soft-Start feature reduces the amount of torque
reaction to the tool and the user. This feature gradu-
ally increases the motor speed up from zero to the
speed set by the variable speed dial.
Feedback Control
(For Cat. No. 5616-20 and 5625-20 only)
The electronic speed control system allows the tool
to maintain constant speed between no-load and
load conditions.
9
Fig. 17 Lock button