Makita DPP200 Manuel D'instruction page 4

Oblong punching
Punch
Unit: mm
Punch
6.5 x 10
(1/4" x 3/8")
6.5 x 13
(1/4" x 1/2")
8.5 x 13
(11/32" x 1/2")
8.5 x 17
(11/32" x 43/64")
9 x 13.5
(23/64" x 17/32")
9 x 18
(23/64" x 23/32")
10 x 15
(3/8" x 19/32")
10 x 20
(3/8" x 25/32")
11 x 16.5
(7/16" x 21/32")
12 x 18
(15/32" x 23/32")
13 x 19.5
(1/2" x 49/64")
14 x 21
(9/16" x 53/64")
Symbols
The followings show the symbols which may be used for the equip-
ment. Be sure that you understand their meaning before use.
Read instruction manual.
Flying debris and loud noise hazards. Wear
ear and eye protection.
Hazardous voltage. Disconnect all power before
working on this equipment. Failure to observe this
instruction may result in death or personal injury.
Die
Die
Mild Steel (65,000 psi)
6.5 x 10B
(1/4" x 3/8"-B)
6.5 x 13B
(1/4" x 1/2"-B)
8.5 x 13B
(11/32" x 1/2"-B)
8.5 x 17B
(11/32" x 43/64"-B)
9 x 13.5B
(23/64" x 17/32"-B)
9 x 18B
(23/64" x 23/32"-B)
10 x 15B
(3/8" x 19/32"-B)
10 x 20B
(3/8" x 25/32"-B)
11 x 16.5B
(7/16" x 21/32"-B)
12 x 18B
(15/32" x 23/32"-B)
13 x 19.5B
(1/2" x 49/64"-B)
14 x 21B
(9/16" x 53/64"-B)
Workpiece
Flat bar
Angle Min: 40 mm (1-37/64") x 40 mm (1-37/64") x t3
Max: 80 mm (3-5/32") x 80 mm (3-5/32") x t8
Channel Min: 75 mm (61/64") x 40 mm (1-37/64")
Max: 100 mm (3-15/16") x 50 mm (1-31/32")
Tensile
t2 - t6
t2 - t6
t2 - t6
t2 - t6
t2 - t6
t2 - t6
t2 - t8
t2 - t8
t2 - t8
t2 - t8
t2 - t8
t2 - t8
Ni-MH
Li-ion
4 ENGLISH
Capacity
Max: 80 mm (3-5/32") x t8
(Center punching)
(Flange punching)
Channel
Stainless Steel (89,000
-
-
-
-
-
-
t7.5
t7.5
t7.5
t7.5
t7.5
t7.5
Moving blade. Keep hands clear while
machine is operating. Turn power off before
servicing.
Only for EU countries
Do not dispose of electric equipment or battery
pack together with household waste material!
In observance of the European Directives,
on Waste Electric and Electronic Equipment
and Batteries and Accumulators and Waste
Batteries and Accumulators and their imple-
mentation in accordance with national laws,
electric equipment and batteries and battery
pack(s) that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility.
Tensile
psi)
t3 - t4
t3 - t4
t3 - t4
t3 - t4
t3 - t4
t3 - t4
t3 - t6
t3 - t6
t3 - t6
t3 - t6
t3 - t6
t3 - t6