FrostEmily PRISMA - DORICA 800 Mode D'emploi page 7

6. CONNECTION TO THE MAINS
1.
Ensure that mains voltage and frequency are the same as those stated on the rating plate
2
to the appliance. . Ensure that the supply socket has the following characteristics:
earthed. It fulfils the requirements of the rated current as set out on the rating plate.
b)
the IEC regulations: - magnetothermal differential switch (also known as ground fault interrupter) with In
= nominal value as stated on the rating plate; - Differential with Id sensitivity = 30 mA. 3. Ensure that
there is no danger of explosion (AD) in the room
designed for internal use. . Connect the plug (do not use three-way adapters and reduction adapters).
N.B. If during transport or storage the appliance has been placed by mistake in a horizontal position or
has been turned upside down, leave for at least three hours in the correct position before switching on the
power supply (see figure 5).
7. CONTROLS
The appliance features adjusting controls, located at the front of the cabinet.
on the light inside the display cabinet.
3. Thermometer:
to display the temperature in the appliance.
the appliance. a) Press button
changed by pressing button
to set the rotating shelves into motion.
3. Refrigeration switch: to switch on the refrigeration system (see figure 6).
8. CHECKING CORRECT OPERATION
Check that: 1.
The plug is connected.
3.
The thermometer shows the desired temperature for the goods to be stored.
exposed to direct sunlight or to high-powered lamps. . The room temperature does not exceed that in
which the appliance is designed to work normally, i.e. +25°C, 60% r.h. (climatic class 3).
draughts coming from doors, windows, fans or conditioner outlets directed towards the appliance.
N.B.: the appliance must be correctly filled, without overloading the shelves and with sufficient space for
correct cold air circulation.
9. INTERNAL CLEANING (EVERY 15 DAYS)
1.
800 TBS/PF models: Switch off the appliance.
3.
refrigerated place. Leave the door open and completely defrost the appliance. . Remove the plug from
the inside of the display cabinet.
6.
evaporator. Dry with care.
TNV/PF models: 1.
Switch off the appliance. . Open the door and remove the refrigerated goods.
3. Wipe the sides and accessories with a sponge dipped in water with a little sodium bicarbonate. Dry
with care (see figure 7).
10. REPLACING THE INTERNAL LIGHTS
1.
Switch off the appliance. . Undo the screws which hold the top lamp socket in place
fluorescent tube with its protective cover from the top lamp socket. . Take the tube out of the bottom
5
lamp socket. . Remove the protective cover. . Replace the fluorescent tube. . Reassemble by following
the above instructions in reverse order (see figure 8).
11. REPLACING THE DOOR'S MAGNETIC GASKET
1. 2
Open the door. . Take hold of the magnetic gasket and pull it out of the frame.
gasket and press it firmly down all around (see figure 9).
Operator's guide
. 4
. The connecting cable to the appliance is H05 VVF,
5
2. Refrigeration switch:
5 "SET or P"
once to display the temperature set-point, which can be
6 "UP 7 "DOWN"
" or button
2. Light switch:
2.
The refrigeration unit switch is switched on (green light on).
2.
5
. Do not use sharp or pointed metal tools to remove the ice from the
7.
Leave the appliance to dry with the door open before restarting.
2
2
6
1. Light switch:
to switch on the refrigeration system.
Thermostat:
to adjust the temperature in
. 800 TNV/PG-PF models:
to switch on the light inside the display cabinet.
5
Remove the goods, placing them in a suitably
4
7
7
(A)
attached
a) it is properly
It complies with
c)
to switch
1. Rotation switch:
4.
The appliance is not
6.
There are no
4
800
. 3
. Detach the
3.
Insert the new
I
UK
D
E
F
NL
P
S
DK
FIN
B
GR
CZ
EE
LV
LT
H
M
PL
SK
SLO