Starting Up - EINHELL RT RH 24 Mode D'emploi D'origine

Anleitung_RT_RH_24_SPK1:_
Check that it is properly secure by pulling the
tool.
6.4. Tool removal (Fig. 5)
Pull back and hold the locking sleeve (2) and remove
the tool.
6.5. Fitting the additional scroll chuck (Fig. 4)
Clean the scroll chuck (12) before fitting it and
apply a thin coating of drill bit grease to the scroll
chuck shaft.
Pull back and hold the locking sleeve (2).
Turn and push the dust-free scroll chuck (12) into
the tool mounting as far as it will go. The scroll
chuck (12) will lock automatically after the locking
sleeve is released.
Check that it is secure by pulling the scroll chuck
(12).
6.6. Removing the additional scroll chuck (Fig. 5)
Pull back and hold the locking sleeve (2) and remove
the scroll chuck.
6.7 Inserting the bit into the scroll chuck
(Figure 6-7)
Always pull the power plug before making
adjustments to the equipment.
Release the depth stop (7) as described in 6.2
and push it towards the drill handle. This provides
free access to the chuck (12).
Undo the chuck by turning it anti-clockwise with
the supplied chuck key (13).
To ensure that it is perfectly positioned the drill bit
or tool should be inserted as far as possible into
the chuck. After inserting the drill bit or tool,
tighten the chuck (12) by turning the chuck key
(13) clockwise until the drill bit or tool is secure.
Check that the drill bit is secure in the chuck (12).
Check at regular intervals that the drill bit or tool is
secure (pull the mains plug).

7. Starting up

Important.
To prevent all danger, the machine must only be
held using the two handles (5 / 6). Otherwise there
may be a risk of suffering an electric shock if you drill
into cables.
7.1 ON/OFF switch (Fig. 8/Item 4)
First fit a suitable drill bit into the tool (see 6.3).
Connect the mains plug to a suitable socket.
Position the drill in the position you wish to drill.
08.02.2010 12:53 Uhr Seite 15
To switch on:
Press the ON/OFF switch (4)
Continuous operation:
Secure the ON/OFF switch (4) with the locking
button (8).
Important. It may only be locked if the drill is set to
rotate clockwise.
To switch off:
Press the ON/OFF switch (4) briefly.
7.2 Adjusting the speed (Fig. 8/Item 4)
You can infinitely vary the speed whilst using the
tool.
Select the speed by applying a greater or lesser
pressure to the ON/OFF switch (4).
Select the correct speed: The most suitable
speed depends on the workpiece, the type of use
and the drill bit used.
Low pressure on the ON/OFF switch (4): Lower
speed
Greater pressure on the ON/OFF switch (4):
Higher speed
Tip: Start drilling holes at low speed. Then increase
the speed in stages.
Benefits:
The drill bit is easier to control when starting the
hole and will not slide away.
You avoid drilling messy holes (for example in
tiles).
7.3 Preselecting the speed (Fig. 8/Item 11)
The speed setting ring (11) enables you to define
the maximum speed. The ON/OFF switch (4) can
only be pressed to the defined maximum speed
setting.
Set the speed using the setting ring (11) on the
ON/OFF switch (4).
Do not attempt to make this setting whilst the drill
is in use.
7.4 Clockwise/Counter-clockwise switch
(Fig. 8/Item 9)
Change switch position only when the drill is
at a standstill!
Switch the direction of the hammer drill using the
clockwise/counter-clockwise switch (9):
Direction
Clockwise (forwards and drill) Pushed in to the right
Counter-clockwise (reverse)
GB
Switch position
Pushed in to the left
15