Noise/Vibration Information; Declaration Of Conformity - Bosch PST 900 PEL Notice Originale

16 | English

Noise/Vibration Information

Sound emission values determined
according to EN 60745-2-11.
Typically the A-weighted noise levels
of the product are
Sound pressure level
Sound power level
Uncertainty K
Wear hearing protection!
Vibration total values a (triax vector
h
sum) and uncertainty K determined
according to EN 60745:
Cutting board:
a
h
K
Cutting sheet metal:
a
h
K
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2009/125/EC (Regulation
1194/2012), 2011/65/EU, 2014/30/EU, 2006/42/EC in-
cluding their amendments and complies with the following
standards: EN 60745-1, EN 60745-2-11.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
1 609 92A 0R8 | (13.11.14)
dB(A) 86 86
dB 97 97
dB(A) 3 3
2
m/s 11.5 10.0
2
m/s 4.0 2.0
2
m/s 8.5 7.0
2
m/s 2.0 2.0
Henk Becker
Executive Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 30.10.2014
Assembly
 Before any work on the machine itself, pull the mains
plug.
Replacing/Inserting the Saw Blade
 When mounting the saw blade, wear protective gloves.
Danger of injury when touching the saw blade.
Selecting a Saw Blade
An overview of recommended saw blades can be found at the
end of these instructions. Use only T-shank saw blades. The saw
blade should not be longer than required for the intended cut.
Use a thin saw blade for narrow curve cuts.
Inserting the Saw Blade (see figure A1)
If required, remove the dust cover 10 (see "Dust Cover").
Insert the saw blade 19 (teeth in cutting direction) into the
stroke rod 16 until it latches. The SDS lever 17 automatically
snaps to the rear and the saw blade is locked. Do not manually
press the lever 17 toward the rear, otherwise you could dam-
age the machine.
While inserting the saw blade, pay attention that the back of the
saw blade is positioned in the groove of the guide roller 18.
 Check the tight seating of the saw blade. A loose saw
blade can fall out and lead to injuries.
Ejecting the Saw Blade (see figure A2)
 When ejecting the saw blade, hold the machine in such
a manner that no persons or animals can be injured by
the ejected saw blade.
Turn the SDS lever 17 forward towards the contact protector
20 to the stop. The saw blade is released and ejected.
Saw Blade Storage (PST 900 PEL/PST 9500 PEL)
(see figure B)
Up to six saw blades with lengths to 110 mm can be stored in
the saw blade storage 21. Insert the saw blades with the T-
shank into the recess of the saw blade storage intended for this.
Up to three saw blades can be placed on top of each other.
Shut the saw blade storage and slide it to the stop into the
opening of the base plate 7.
Sliding Shoe (PST 1000 PEL)
When working surfaces that are easily scratched, the sliding
shoe 11 can be attached onto the base plate 7 in order to pre-
vent the surface from being scratched.
To attach the sliding shoe 11, insert it at the front of the base
plate 7, push the rear part upward and allow it to latch.
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
Bosch Power Tools