Practical Advice - Bosch PKP 3,6 LI Notice Originale

10 | English
Cordless glue gun
Battery
Rated voltage
Capacity
Number of battery cells
Operating time per battery
charge approx. (according to
Bosch testing procedures)
A) Corresponds to approx. six glue sticks
Charger
Article number
Battery charging voltage
Charge current
Permitted charging
temperature range
Charging time
Protection class
Fitting
Battery Charging (see figure A)
Note the mains voltage! The voltage of the power source
u
must match the voltage specified on the rating plate of
the charger. Chargers marked with 230 V can also be op-
erated with 220 V.
Note: The battery is supplied partially charged. To ensure
the maximum performance of the battery, use the charger to
fully charge the battery before first use.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The Li-ion battery is protected against deep discharge. A
protective circuit switches the glue gun off when the battery
is drained, meaning the adhesive is no longer being heated.
If the battery charge indicator (8) flashes red, the battery
has less than 30% capacity and should be charged. When
the battery is fully charged, the battery charge indicator is
continuously lit red.
To charge the battery, connect the Micro-USB con-
nector (10) of the charging cable (11) to the charging
socket (9) and the USB charging connector (12) to the char-
ger (13). Then plug the mains cable of the charger into the
mains socket.
The battery charge indicator (8) will flash green during the
charging process. When the charging process is complete,
the battery charge indicator will be continuously lit green.
Unplug the charger from the mains.
The glue gun cannot be used during the charging process.
The lack of function during the charging process does not
mean that the tool is defective.
Protect the charger from moisture.
u
1 609 92A 4UL | (17.01.2019)
PKP 3,6 LI Operation
Li-ion
Start-up
V= 3.6
Switching On and Off
Ah 1.5
To switch on the glue gun, press and hold the on/off but-
1
ton (7) until the heating indicator (6) lights up green.
A)
min 30
The heating indicator (6) will flash while the tool is heating
up. Once it is continuously lit, the glue gun is ready to use.
To switch off the glue gun, press and hold the on/off but-
ton (7) until the heating indicator (6) goes out.
Note: If the glue gun is not used for longer than five minutes,
it will switch off automatically to save energy.
2 609 120 7..
When switching on again, check the battery charge indic-
V= 5
ator (8): If it lights up red, the battery needs to be charged.
A 1
Safely place the glue gun down after use and let it cool
u
°C +5 to +40
completely before packing it away. The hot nozzle can
cause damage.
hrs 3−4

Practical advice

/Ⅱ
Keep people and animals away from the hot adhesive
u
and the nozzle tip. Adhesive and nozzle tip will heat up to
170 °C, posing a risk of burns. If hot adhesive comes into
contact with skin, immediately hold the affected area un-
der a stream of cold water for several minutes. Do not try
to remove the hot adhesive from the skin.
Only use adhesives that have been recommended by the
manufacturer of the glue gun.
Adhesive bonds can become unstuck when they are affected
by moisture.
Preparing for gluing
The bonding locations must be clean, dry and free from
grease.
The materials to be glued together and the work surface
must not be easily ignited or flammable.
Test whether heat-sensitive materials are suitable before-
hand on a sample workpiece.
The ambient temperature and the workpieces to be glued
must not be colder than +5 °C and not warmer than +50 °C.
Materials that cool the adhesive down quickly should be
warmed first with a hot air gun.
Gluing
Push the glue stick (4) suited to the material into the glue
stick compartment (5).
Switch on the glue gun and allow it to heat up. The heating
indicator (6) will flash during heating.
Once the heating indicator (6) is continuously lit, the glue
gun is ready to use.
Apply moderate pressure to the feed trigger (3).
Apply the adhesive to a single side.
Press the materials you wish to glue together against each
other for around 10 to 30 seconds immediately after apply-
ing the adhesive. It is still possible to correct the bonding
location at this point.
The bond is stable after approx. two minutes of cooling time.
Bosch Power Tools