Maintenance; Maintenance Schedule - Husqvarna LC 141iV Manuel D'utilisation

Tondeuse rotative à pousser
Masquer les pouces Voir aussi pour LC 141iV:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 187
1. Release the motor brake handle to stop the motor.
(Fig. 25)
2. Press the ON/OFF button (A) on the control panel
and the green LED (B) goes out. (Fig. 51)
3. Open the battery lid and turn the safety key to 0.
(Fig. 52)
4. To remove the battery, press the 2 release buttons
and pull out the battery. (Fig. 53)
5. Charge the battery if it is weak. For more
To charge the battery on page 19 .
information, see
To operate LC 141C
To select an approved cable (LC 141C)
Note: For the UK market, use only the 16M extension
cable that comes with the product. For all other markets,
refer to the information below.
If extension cables are used, these must comply with the
minimum cross-sections in the table below:
Voltage
Cable length
220-240V/ 50Hz
Up to 20 m
220-240V/ 50Hz
20–50 m
Mains cables and extension cables are available
from your local approved service agent for
Husqvarna outdoor products.
Only use extension cables specifically designed for
outdoor use and which conform to one of the
following specifications: Ordinary rubber (60245 IEC
53), Ordinary PVC (60227 IEC 53) or Ordinary PCP
(60245 IEC 57)
If the cable is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
Introduction
WARNING: Before you do maintenance,
you must read and understand the safety
chapter.
For all servicing and repair work on the product, special
training is necessary. We guarantee the availability of
professional repairs and servicing. If your dealer is not a
service agent, speak to them for information about the
nearest service agent.
LC 141iV, LC 141i and LC 141C
Do a general inspection.
Clean the product.
20
To start the product
1. Connect a power cord to the socket below the
2. Put the power cord in the power cord holder. Refer
3. Stay behind the product.
4. Loosen the start inhibitor. (Fig. 46)
5. Push the motor brake handle in the direction of the
To stop the product
1. Release the motor brake handle to stop the motor.
2. Disconnect the power cord from the mains and then
Cross section
To get a good result
2
1.5 mm
2
2.5 mm

Maintenance

Maintenance schedule

The maintenance intervals are calculated from daily use
of the product. The intervals change if the product is not
used daily.
For maintenance identified with *, refer to
on the product on page 14 .
handle. (Fig. 54)
To use the power cord holder (model LC 141C) on
to
page 14 . (Fig. 28)
handlebar. (Fig. 55)
(Fig. 56)
from the product. (Fig. 57)
CAUTION: Pull the plug straight out. Do
not pull the power cord.
Always use a sharp blade. A blunt blade gives an
irregular result and the cut surface of the grass
becomes yellow. A sharp blade also uses less
energy than a blunt blade.
Do not cut more than ⅓ of the length of the grass.
Cut first with the cutting height set high. Examine the
result and lower the cutting height to an applicable
level. If the grass is very long, drive slowly and cut 2
times if necessary.
Cut in different directions each time to prevent
stripes in the lawn.
Each
use
X
X
Safety devices
Each
Monthly
season
919 - 001 - 19.10.2018

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Lc 141iLc 141c

Table des Matières