Whirlpool WED7500GW Guide D'utilisation Et D'entretien page 13

If you experience
Clothes are not drying Fabric softener sheets are blocking
satisfactorily, clothes are the grille.
balling or tangling, or
The dryer is located in a room
drying times are
with temperature below 45ºF (7ºC).
too long (cont.)
The dryer is located in a closet.
Clothes are getting The automatic cycle settings are
too high or too low.
over or under dried
Cycle time is too short The load may not be contacting the
sensor strips on automatic cycles.
The automatic cycle is ending early.
Lint on load Lint screen is clogged with lint.
Stains on load Improper use of fabric softener.
Stains on drum Loose dyes in clothes.
Loads are wrinkled The load was not removed from dryer
at the end of the cycle.
The dryer was tightly packed.
Odors Recent painting, staining, or
varnishing in the area where your
dryer is located.
Load too hot Load removed before cooldown
portion of cycle complete.
Using Timed Dry cycle with a high
temperature setting.
Dryer Displaying Code Message or Indicator Is Lit
"PF" (power failure) The drying cycle has been interrupted
by a power failure.
"L2" Diagnostic Code There may be a problem with your
(low or no line voltage home power supply, keeping the
condition) dryer's heater from turning on.
"F# E#" (F1 E1, F3 E1, The dryer is in need of service.
etc.) variable
service codes.
Possible Causes
Check that the air outlet grille is not blocked by a fabric softener
sheet. Use only one fabric softener sheet, and use it only once.
Proper operation of dryer cycles requires temperatures
above 45ºF (7ºC).
Closet doors must have ventilation openings at the top and
bottom of the door. The front of the dryer requires a minimum
of 1" (25 mm) of airspace, and, for most installations, the rear of
the dryer requires 6" (152 mm). See the Installation Instructions.
See "Changing the automatic cycle settings to increase or
decrease drying time" to adjust your dryer settings.
Level the dryer. See the Installation Instructions. All four dryer feet
should be in firm contact with the floor.
Change the dryness level setting on automatic cycles. Increasing
or decreasing the dryness level will change the amount of drying
time in a cycle. If loads are consistently ending too early, see also
"Changing the automatic cycle settings to increase or decrease
drying time."
Clean lint screen before each load.
Add dryer fabric softener sheets at the beginning of the cycle.
Fabric softener sheets added to a partially dried load can stain
your garments.
Drum stains are caused by dyes in clothing (usually blue jeans).
These will not transfer to other clothing.
Select the Wrinkle Shield option to tumble the load without heat
to avoid wrinkling.
Dry smaller loads that can tumble freely. Results may also vary
depending on fabric type.
Ventilate the area. When the odors or fumes are gone from
the area, rewash and dry the clothing.
Allow the dryer to complete the cooldown portion of the cycle
before removing the load.
Select an automatic cycle with a lower heat setting to avoid
overdrying the load.
Touch and hold START/PAUSE to restart the dryer cycle or touch
power to clear the display.
The dryer will continue to run when this diagnostic code is
present. Touch any pad to clear the code from the display
and return to the estimated time remaining.
NOTE: This error will only show during the initial installation.
Try the following:
Check to see if a household fuse has blown or a circuit
■
breaker has tripped. Electric dryers use two household fuses
or breakers. Replace the fuse or reset the circuit breaker.
Confirm that the power cord is properly installed. Refer
■
to the Installation Instructions for details.
Select a Timed Dry heated cycle, and restart the dryer.
■
If the message persists, consult a qualified electrician.
If a code beginning with an "F" appears in the display, alternating
between F# and E#, the dryer control has detected a problem
that requires service. Call for service.
Solution
13