Advanced Configuration; Built-In Timer; Maintenance - Espa evopool Silenplus Manuel D'instructions

6.3 Deactivation.
To deactivate Filterwatch:
- Press "M" for 5 seconds.
- The "Filtration Plus" LED will blink 3 times.
The Filterwatch function will be deactivated and
the Filtration Plus LED will stop blinking.
6.4 System control.
You can activate and deactivate Filterwatch
and control the system status through the
EspaEvopool application.

7. ADVANCED CONFIGURATION

Different speeds can be set to adjust the functions
to the characteristics of the installation.
The function being run will be configured.
To configure a function, first select it, either in Man-
ual or Remote mode, and at the same time press M
+ F for 5 seconds.
All the speeds of the selected function will return to
the factory settings [= fs]
To increase or decrease the speed, press M or F:
M = + 1 Hz
F = - 1 Hz
 Configuring Filtration Plus.
The filtration speed is set.
· Minimum = 20 Hz (1,600 RPM), [= fs]
· Maximum = 50 Hz (2,900 RPM)]
 Configuring Backwash Plus.
The maximum and minimum speeds are set, al-
ways maintaining a differential of 20 Hz between
them
· Minimum = 20/40 Hz (1,600/2,320 RPM), [= fs]
· Maximum = 30/50 Hz (1,740/2,900 RPM)
 Configuring the Mixed Cycle (Manual only)
The factory setting is 2,320 RPM (40 Hz)
· Minimum = 20 Hz (1,600 RPM)
· Maximum = (50 Hz (2,900 RPM)
If M and F are not pressed for 5 seconds the new
values are stored and the configuration mode is
deactivated.
Silenplus can also be entirely configured us-
ing the EspaEvopool application.

8. BUILT-IN TIMER

The Silenplus pump has an internal clock that can
operate as a start and stop timer, making external
programming unnecessary.
With this function, Silenplus can operate entirely
independently.
ATTENTION: the programming and mainte-
nance of the timer is only possible through
the EspaEvopool app.
8.1 Activating the timer.
DANGER. Electrocution risk.
Never open the Silenplus cover without
turning the power supply off at least 5
minutes beforehand.
 Lift the Silenplus cover by loosening the 4
screws. (See figure 6)
 Activate the Timer using the mini-switch, moving
it to the "ON" position.
 Replace the cover and fix it with the 4 screws.
Torque: 0.5 Nm.
8.2. Time setting.
Link Silenplus with the external device using Blue-
tooth, following the instructions on the device.
Run the EspaEvopool app and follow its indica-
tions.

9. MAINTENANCE

ControlSystem:
If ControlSystem is not communicating with
Silenplus it may be necessary to replace the
battery. Proceed as in figure 7.2.
It is a 1.5 V, CR2450 type battery.
Silenplus:
Our Silenplus equipment is maintenance free.
The Silenplus time programmer works with a
CR1220 3V battery. To replace
according to figure 7.1
Clean the equipment with a damp cloth and without
using aggressive products.
In freezing weather, take the precaution of
emptying the pipes.
If the equipment is going to be inactive for a
long time, you are recommended to disman-
tle it and keep it in a dry, well-ventilated place.
WARNING: in case of a breakdown, the
equipment must only be touched by an au-
thorised service technician.
The list of official technical services can be found at
www.espa.com.
When the time comes to throw the product away, it
does not contain any toxic or polluting material. The
main components are duly identified so you can
dispose of them selectively.
This product or parts of it must be disposed of in an
environmentally sound way, use the waste collec-
tion service. If this is not possible, contact the
nearest ESPA service workshop.
15
EN
it proceed