Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
drastically reducing the amount of water used for effi-
cient cleaning.
EFFECTIVENESS: reduction of backwash time and
improved filter-cleaning efficiency.
SAVINGS: a minimum of 25% water savings over
standard pumps.
:
The rotational speed of the pump automatically adapts
to the normal and progressive clogging of the filter so
as not to reduce the effectiveness of the
function.
2. HANDLING
It is supplied in suitable packaging to prevent it deteri-
orating during transport. Before unpacking the product,
check that the packaging has not suffered damage or
is misshapen.
Handle the product carefully, with the right tools.
3. INSTALLATION
This equipment is designed for use indoors.
3.1. Pump installation.
WARNING: Follow the installation manual in-
structions for the standard pump.
3.2. Electrical connection
The electrical installation must have a multiple
separation system with a 3 mm contact opening.
The system's protection will be based on a dif-
ferential switch (Δfn = 30 mA).
The equipment is supplied with a power cable with plug.
Do not manipulate the equipment.
3.3
installation
Fit the
to the multiport filter valve con-
trol. (See figure 1)
Select a location as near as possible to the turning
centre.
Clean the surface with alcohol.
Lift
the
protective
into the chosen place.
Watch the "
should be closer to the rotation axis.
Secure the assembly by tightening the tape under
the control. Check that it is fixed properly.
4. START-UP
4.1 Starting up the equipment.
Follow the installation manual instructions for the
pump to start it up properly.
4.2. Initial configuration
The first time you start it up you need to link
with
(See figure 2)
WARNING: It is very important to follow the or-
der of the operations described here:
stickers
and
plug
the
" position. Screw area
4.2.1 Starting up the
Connect the
The system will start up and a set of lights indicates
that it has been activated.
If a
has not already been linked to it,
the pump will not start up.
is on standby waiting for the link to be estab-
lished. The 3 leds flash together.
4.2.2 Activating the
To prevent the battery running out before the equip-
ment is started up, the ControlSystem has an internal
ON/OFF switch that must be activated (See figure 2)
CAUTION: Do not approach magnetic elements
to
Ensure that no magnetic fields can affect the
proper operation of the system.
WITH
THE
PUMP
ELECTRICAL CURRENT (see 4.2.1):
Make sure the valve is in the intermediate position
between 1 and 4
Lift the cover, loosening the screw.
Activate the
switch to the "ON" position.
When the battery is connected,
mits a unique code for an interference-free link.
Flashing leds indicate that proper communication has
been achieved. The green LED will light.
Replace the cover and fix it with the screw.
Torque: 0.2 Nm.
4.2.3 Calibrating the
The 6 valve positions must be indicated to the system.
For this purpose, use the following calibration process
(See Figure 3):
Move the valve control to position 4. Wait for the
green LED is illuminated.
Move the valve control to position 6. Wait for the
green LED is illuminated.
Move the valve control to position 2. Wait for the
green LED is illuminated.
Move the valve control to position 5. Wait for the
green LED is illuminated.
Move the valve control to position 3. Wait for the
green LED is illuminated.
Move the valve control to position 1.
The pump will start up in Remote
The corresponding LED will come on.
4.3 Multiple system
In an installation with several pieces of equipment,
must be started up and the
activated in order.
Each piece of equipment is linked using a unique code
to prevent interference between them.
A
pump in standby mode will be linked to the
first
activated.
WARNING: activate the
valve for the pump on standby.
10
EN
pump to the power supply.
during this operation.
CONNECTED
TO
by moving the mini-
trans-
mode.
of the
THE
Publicité
Chapitres
Table des Matières
