General Safety Precautions; Ec Declaration Of Conformity; Applications - DITEC UP8E Manuel D'installation Et D'entretien

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 12

GENERAL SAFETY PRECAUTIONS

GB
This installation manual is intended for professionally
competent personnel only. Installation, electrical connec-
tions and adjustments must be performed in accordance
with Good Working Methods and in compliance with applicable
regulations. Before installing the product, carefully read the
instructions.
Bad installation could be hazardous.
The packaging materials (plastic, polystyrene, etc.) should not
be discarded in the environment or left within reach of children,
as these are a potential source of hazard. Before installing the
product, make sure it is in perfect condition.
Do not install the product in an explosive environment and atmos-
phere: gas or infl ammable fumes are a serious hazard risk.
Before installing the motors, make all structural changes relat-
ing to safety clearances and protection or segregation of all
areas where there is risk of being crushed, cut or dragged, and
danger areas in general. Make sure the existing structure is up
to standard in terms of strength and stability.
The motor manufacturer is not responsible for failure to use
Good Working Methods in building the frames to be motorised
or for any deformation occurring during use.
The safety devices (photocells, safety edges, emergency stops,
etc.) must be installed taking into account: applicable laws and
directives, Good Working Methods, installation premises, system
operating logic and the forces developed by the motorised door
or gate. The safety devices must protect any areas where the
risk exists of being crushed, cut or gragged, or where there are
any other risks generated by the motorised door or gate.
Apply hazard area notices required by applicable regulations.
Each installation must clearly show the identifi cation details of
the motorised door or gate.
Before making power connections, make sure the plate details
correspond to those of the power mains.
Fit an omnipolar disconnection switch with a contact open-
ing gap of at least 3 mm. Make sure an adequate residual current
circuit breaker and overcurrent cutout are fi tted upstream of the
electrical system. When necessary, connect the motorised door
or gate to a reliable earth system made in accordance with ap-
plicable safety regulations.
During installation, maintenance and repair, interrupt the power
supply before opening the lid to access the electrical parts.
To handle electronic parts, wear earthed antistatic conductive
bracelets.
The motor manufacturer declines all responsibility in the event
of component parts being fi tted that are not compatible
with the safe an correct operation.
For repairs or replacements of products only original spare parts
must be used.
The installer shall provide all information relating to automatic,
manual and emergency operation of the motorised door or gate,
and provide the user with operating instructions.

APPLICATIONS

Service life: 4 (minimum 10÷5 years of working life with 100÷200
cycles a day).
Applications: INTENSIVE (For all special applications with
ongoing use such as toll gates and so on).
-
Performance characteristics are to be understood as refer-
ring to the recommended weight (approx. 2/3 of maximum
permissible weight). A reduction in performance is to be ex-
pected when the access is made to operate at the maximum
permissible weight.
UP8 - IP1782
-
Service class, running times, and the number of consecu-
tive cycles are to be taken as merely indicative having been
statistically determined under average operating conditions,
and are therefore not necessarily applicable to specifi c condi-
tions of use. During given time spans product performance
characteristics will be such as not to require any special
maintenance.
-
The actual performance characteristics of each automatic
access may be affected by independent variables such as
friction, balancing and environmental factors, all of which
may substantially alter the performance characteristics of the
automatic access or curtail its working life or parts thereof
(including the automatic devices themselves). When setting
up, specifi c local conditions must be duly borne in mind and
the installation adapted accordingly for ensuring maximum
durability and trouble-free operation.
MACHINE DIRECTIVE
The installer who installs and starts a power operated door or
gate to his name, becomes the manufacturer according to the
Machine Directive (98/37/EC) and shall: prepare technical fi le,
draw up the EC declaration of conformity, affi x the CE mark-
ing.
For more details, refer to the " EC Guidelines" available on
Internet at the following address: http://www.ditec.it

EC DECLARATION OF CONFORMITY

Manufacturer: DITEC S.p.A.
Address: via Mons. Banfi , 3 - 21042 Caronno P.lla (VA) - Italy
declares that the product power operated barrier type: UP8
complies with the essential requirements of the following EC
directives:
- EMC Directive 89/336/EEC
- Machinery Directive 98/37/EC
- Construction Products Directive 89/106/EEC
complies with the following characteristics of EN 13241-1 stand-
ard (Annex ZA):
- Factory production control (Pass)
- Release of dangerous substances (Pass)
- Resistance to wind load (Class 5)
- Safe opening (Pass)
- Mechanical resistance and stability (Pass)
- Operating forces (Pass)
Notifi ed Body: Treviso Tecnologia - CERT
Registration number: 1600
Address: Via Pezza Alta, 34 – 31046 Rustignè di Oderzo (TV)
Caronno Pertusella, 2005-05-01
Caronno Pertusella, 2005-05-01
8
Fermo Bressanini
Fermo Bressanini
(Chairman)
(Chairman)

Publicité

Table des Matières
loading

Table des Matières