Installation Completed; Optional Extras - Jøtul FS 162 Advance Manuel D'installation Et D'utilisation

11. Make sure that the fl exible tube for combustion air is
not trapped. This tube is passed through an opening in the
bottom stone. If external air connection is not going to be
used, cut the fl ex hose at the outer edge of the opening.
Suggested installation of the fl ex hose for combustion air:
See fi g. 11B and C. Remove the pieces of wood carefully
so that the burn chamber does not topple over. Installation
completed: See fi g. 11 D.
6. The approval label, which is attached by a wire, is fed under
the burn chamber.
7. Attach the locking bracket (part 8) to the load-bearing plate
using the screws provided (part 32). See fi g. 12.
8. Position the lower cover plate (part 9). See fi g. 13.
9. Position the side cartridge with stone fi tted (parts 10, 11 and
12), fi g. 14. Positioning pin with slot must face upwards.
10. Attach 2 brackets (part 42) to the upper cover plate with 2
screws + nuts with washers.
11.Fit upper cover plate (part 13) using the wedges provided (part
14), fi g. 15. Fit wedges in towards the centre of the stove.
Fitting with a top outlet
The product is supplied from the factory with smoke outlet fi tted
for the top outlet.
• Fit an off set pipe, 60 mm (optional extra).
• Make sure that the gasket is properly seated
between the off set pipe and the smoke outlet.
11. Fit layers 2 and 3 with the relevant brackets.
12. Fit layer 4.
13. Position the two-piece top stone (part 18), Fig. 17.
14. Insert valve plates 1 and 2 (parts 19 + 20).
Fig. 18 + 19.
• Thread the fl ue pipe through the valve plates and place it in
the off set centre pipe.
• Side stones for smoke outlet (parts 16 and 17) should not
be used if using top outlet.
Fitting with a rear outlet at height of 1050 mm
Select stones with holes bored in them for the back stones. Two
of the side stones (part 15) should not be used with rear outlet.
• Use the smoke outlet installed for the top outlet.
• Fit the fl ue pipe with the smoke outlet on it from the inside of
the burn chamber, then attach the smoke outlet using screws
M8x30mm. NOTE: If the fl ue pipe is more than 350 mm long,
the fl ue pipe is pushed into the smoke outlet from the back
of the product. It is important for the joints/fl ue pipes to be
sealed completely. Air leaks may stop them functioning.
11. Fit layers 2 and 3 with the relevant brackets.
12. Fit layer 4 and additional height if required.
13. Position the two-piece top stone (part 18), Fig. 17.
14. Insert valve plates 1 and 2 (parts 19 + 20). Fig. 18 + 19.
15. Replace the burn plates, baffl e, exhaust defl ector, inner
bottom, ash pan and riddling grate.
Fitting with a rear outlet at height of 1416 mm
Select stones with holes drilled in them for the rear stones in
layer no. 4. Two of the side stones (part 15) should not be used
with rear outlet.
The product is supplied from the factory with the smoke outlet
fi tted for the top outlet.
• Use the smoke outlet installed for the top outlet.
• NOTE: It is important for the joints/fl ue pipes to be sealed
completely. Air leaks may stop them functioning.
11. Fit layers 2 and 3 with the relevant brackets.
12. Fit layer 4.
13. Fit the fl ue pipe with a 90
with the instructions from the smoke outlet to the chimney.
(See "4.2 Chimney and fl ue pipe".
14. Fit additional height if required.
15. Position the two-piece top stone (part 18), Fig. 17.
16. Insert valve plates 1 and 2 (parts 19 + 20). Fig. 18 + 19.
17. Replace the burn plates, baffl e, exhaust defl ector, inner
bottom, ash pan and riddling grate.
Fitting with a rear outlet at height of 1781
mm (with additional height)
Select stones with holes drilled in them for the rear stones in
layer no. 4. Two of the side stones (part 15) should not be used
with rear outlet.
The product is supplied from the factory with the smoke outlet
fi tted for the top outlet.
• Use the smoke outlet installed for the top outlet.
• NOTE: It is important for the joints/fl ue pipes to be sealed
completely. Air leaks may stop them functioning.
11. Fit layers 2 and 3 with the relevant brackets.
12. Fit layer 4 and additional height.
13. Fit the fl ue pipe with a 90
with the instructions from the smoke outlet to the chimney.
(See "4.2 Chimney and fl ue pipe".
14. Position the two-piece top stone (part 18), Fig. 17.
15. Insert valve plates 1 and 2 (parts 19 + 20). Fig. 18 + 19.
16. Replace the burn plates, baffl e, exhaust defl ector, inner
bottom, ash pan and riddling grate.

5.0 Installation completed

See the General user and maintenance manual for Jøtul F 370
Advance for use and maintenance of the product!
5.1 Maintenance
If you have the misfortune to fi nd scratches in the surface, these
may be polished out using a fi ne sandpaper. If deeper scratches
are present, a paste made of powdered soap stone and water
glass can be made up which you can use to fi ll the stone.

5.2 Optional extras

Floor plate, steel
Cat. no. 51013582
Kit for additional height
Cat. no. 50012997
See fi g. 6 for the position of the module.
Off set pipe, 60 mm
Cat. no. 51013631
External air connection
Cat. no. 51012164
ENGLISH
bend (not included) in accordance
0
0 bend (not included) in accordance
23