Replacing The Blade; Ordering Replacement Parts; Disposal And Recycling; Storage - EINHELL GE-CM 36/37 Li Mode D'emploi D'origine

•
Ensure that all mounting components (i.e.
screws, bolts, nuts etc.) are always tightened
so that the equipment can be safely operated
at all times.
•
Check the grass catch assembly frequently
for signs of wear.
•
Replace excessively worn or damaged parts
immediately.
•
In order to ensure that you enjoy the
equipment for many years to come, all
screwed parts, as well as the wheels and
axles, should be cleaned and lubricated.
•
Keeping your lawn mower in good condition
not only ensures a long lifespan and high
performance, but also enables the equipment
to thoroughly cut your grass with minimal
effort.
•
The blade is subjected to more wear and
tear than any other component. Therefore,
routinely check the condition of the blade
and make sure that it is tightly fastened. If
the blade is completely worn out, it must be
immediately replaced or ground sharp again.
An excessively vibrating mower means that
the blade is not properly balanced or has
become deformed from striking an object.
In this case, the blade must be repaired or
replaced.
•
There are no other parts inside the equipment
which require maintenance.

7.4 Replacing the blade

For safety reasons, we recommend having the
blade replaced by an authorized professional.
Caution! Pull out the safety plug! Wear work
gloves! Only replace the blade with a genuine
Einhell replacement blade, as this will ensure top
performance and safety under all conditions.
Carry out the following steps to change the blade:
1. Undo the fastening screw with the help of the
supplied open-ended wrench (Fig. 15/Item
20)).
2. Remove the blade and replace with a new
one.
3. When fi tting the blade, make sure it is
installed in the right direction. The blade's
air vanes must project into the motor
compartment (see Fig. 15). The dome mounts
must be aligned with the punch holes in the
blade.
4. Then retighten the fastening screw with the
universal wrench. The tightening torque
should be approx. 221 in.-lbs (25 Nm).
Anl_GE_CM_36_37_Li_USA.indb 17 Anl_GE_CM_36_37_Li_USA.indb 17
EN
At the end of the season, perform a general
inspection of the lawn mower and remove any
grass and dirt which may have accumulated.
At the start of each season, ensure that you
check the condition of the blade. If repairs are
necessary, please contact our customer service
center. Use only genuine spare parts.

7.5 Ordering replacement parts:

Service
1. If your power tool requires service,
contact an authorized Einhell USA dealer
or call the Einhell USA customer service
center at 1-866-EINHELL
(1-866-346-4355). Only identical
replacement parts should be utilized for
repairs. This will ensure that the safety of the
power tool is maintained.
2. If the battery charger cable is damaged, it
must be immediately replaced to avoid a
hazard. Contact the Einhell USA
service center at 1-866-EINHELL
(1-866-346-4355) for assistance.
Spare blade Art. No.: 34.054.86

8. Disposal and recycling

The equipment is supplied in packaging to
prevent it from being damaged in transit. The
raw materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council offi ces.

9. Storage

Store the equipment and its accessories out
of children's reach in a dark and dry place at
above freezing temperature. The ideal storage
temperature is between 41°F and 86°F
(5°C and 30°C). Keep the electric tool in its
original packaging.
- 17 -
customer
®
23.09.2020 11:17:46 23.09.2020 11:17:46