Precautions For Use - Yamaha R-S202 Mode D'emploi

• When turning on the power to the audio system, always turn on the
power to the power amplifier LAST. When turning off the power to the
audio system, turn off the power to the power amplifier FIRST.
Otherwise, hearing loss or damage to the product may be caused.
Maintenance
• Before cleaning the product, be sure to remove the power cord plug
from the AC outlet.
Otherwise, electrical shock may be caused.
Handling
• Do not touch the surface to which this label is attached.
The surface may become heated during use of this product, and
touching the surface may result in burns.
• Do not drop a foreign object, such as a piece of metal or paper, into any
gap on this product.
Otherwise, fire, electrical shock or damage to the product may be
caused.
• Keep small parts away from infants.
Otherwise, they may swallow them by accident.
• Do not apply the following excessive force to this product.
- Resting your weight on this product
- Placing heavy objects on this product
- Stacking up this product
- Applying excessive force to the buttons, switches, or I/O connectors
Otherwise, injury or damage to the product may be caused.
• Do not pull connected cables.
Otherwise, the product may fall or tip over, resulting in injuries or
damage to the product.

Precautions for use

NOTICE
Follow the precautions below to avoid malfunction and damage to this
product and to prevent the loss of data.
Power supply
• If you plan not to use this product for a long period of time, remove the
power cord plug from the AC outlet. Even when the [A] (Standby/On)
switch is turned off, a small amount of current still flows through this
product.
Installation
• Depending on the environment in which you use the product, a phone,
radio or TV may generate noise. In that case, change the product
location or orientation, or the surrounding environment.
• Do not install this product in a place subject to:
- Direct sunlight
- Extremely high or low temperatures
- Excessive dust
Otherwise, malfunction or damage to the product may be caused.
• Do not install this product in a place where condensation can form due
to rapid, drastic changes in ambient temperature. Using the product
while condensation is present may cause damage to the product. If
there is a reason to believe that condensation might have occurred on
or in this product, leave it for several hours without turning on the
power. You can start using the product when the condensation has
completely dried.
• Do not install this product in the vicinity of a:
- Metal wall or desk
- Microwave oven
- Wireless LAN device
- Wireless microphone transmitter
Otherwise, the quality of the radio waves may be degraded, resulting in
unstable wireless communication.
iii
En
Handling
• Do not place any vinyl, plastic or rubber products on this product.
Otherwise, the panel may be discolored or deteriorate.
Maintenance
• Use a dry, soft cloth to clean this product. Do not use benzine, thinner,
detergent or chemical rag to clean the surface of the product.
Otherwise, the surface may be discolored or deteriorate.
Important information
NOTE
This section describes precautions to be observed during use, functional
restrictions, and supplemental information that may be helpful for you.
Disposal or transfer
• If you plan to transfer ownership of this product, include this document
and the supplied accessories along with the product.
• Follow the rules of your local authority to dispose of this product and
its accessories.
• Follow the rules of your local authority to dispose of used batteries.
This equipment complies with ISED radiation exposure limits set
forth for an uncontrolled environment and meets RSS-102 of the
ISED radio frequency (RF) Exposure rules. This equipment should be
installed and operated keeping the radiator at least 20 cm or more
away from person's body.
This device contains licence-exempt transmitter(s)/receiver(s) that
comply with Innovation, Science and Economic Development
Canada's licence-exempt RSS(s). Operation is subject to the
following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference
that may cause undesired operation of the device.