Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
•
Use appropriate and required safety equipment, as
instructed in the Specific Safety Rules.
•
Secure and maintain work area, as instructed in the
Specific Safety Rules.
•
Run the drill very slowly, using light pressure, until the
hole is started enough to keep the drill bit from slipping
out of it.
•
Apply pressure in a straight line with the bit. Use
enough pressure to keep the bit biting but not so much
as to stall the motor or deflect the bit.
•
hold the drill firmly with two hands to control its
twisting action.
•
DO NOT CLICK THE TRIGGER OF A STALLED DRILL OFF
AND ON IN AN ATTEMPT TO START IT. DAMAGE TO THE
DRILL CAN RESULT.
•
Minimize stalling on breakthrough by reducing pressure
and slowly drilling through the last part of the hole.
•
Keep the motor running while pulling the bit out of a
drilled hole. This will help reduce jamming.
•
Make sure switch turns drill on and off.
Drilling in Wood
Holes in wood can be made with the same twist drill bits
used for metal or with spade bits. These bits should be
sharp and should be pulled out frequently when drilling to
clear chips from the flutes.
Drilling in Metal
Use a cutting lubricant when drilling metals. The exceptions
are cast iron and brass which should be drilled dry. The
cutting lubricants that work best are sulfurized cutting oil or
lard oil.
Drilling in Masonry
Use carbide tipped masonry bits. Refer to Drilling section.
Keep even force on the drill but not so much that you crack
the brittle material. A smooth, even flow of dust indicates
the proper drilling rate.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
iMPORTAnT: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment should be performed
by authorized service centers or other qualified service
organizations, always using identical replacement parts.
Cleaning
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool or power supply; never immerse any
part of the tool or power supply into a liquid.
nOTE: Remove tool from GoPak before cleaning.
Use only mild soap and a damp cloth to clean the tool or
power supply. Many household cleaners contain chemicals
which could seriously damage plastic. Also, do not use
gasoline, turpentine, lacquer or paint thinner, dry cleaning
fluids or similar products.
Blow dirt and dust out of all air vents with clean dry air.
WARNING: To minimize the risk of eye injury, always
wear ANSI Z87.1 approved eye protection.
TROUBLESHOOTING
1. The GoPak will not power your device or charge.
a. The LED closest to the state of charge button will
blink red when attempting USB functionality.
-
The GoPak is too hot or too cold. Allow the GoPak to
cool down or warm up.
2. The GoPak will not power your compatible tool.
-
Attempt to charge the battery. If the LED fails to
come on refer to number 1 in Troubleshooting.
Repairs
The BLACK+DECKER GoPak 2 in 1 battery is not serviceable.
WARNING: To assure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(including brush inspection and replacement) should
be performed by a BLACK+DECKER factory service
center or a BLACK+DECKER authorized service center.
Always use identical replacement parts.
TWO-YEAR LIMITED WARRANTY
Black & Decker (U.S.) Inc. warranties this product to be free
from defects in material or workmanship for a period of
two (2) years following the date of purchase, provided that
the product is used in a home environment. This limited
warranty does not cover failures due to abuse, accidental
damage or when repairs have been made or attempted
by anyone other than BLACK+DECKER and its Authorized
Service Centers. A defective product meeting the warranty
conditions set forth herein will be replaced or repaired at no
charge in either of two ways:
The first, which will result in exchanges only, is to return
the product to the retailer from whom it was purchased
(provided that the store is a participating retailer). Returns
should be made within the time period of the retailer's
policy for exchanges. Proof of purchase may be required.
Please check with the retailer for its specific return policy
regarding time limits for returns or exchanges.
The second option is to take or send the product
(prepaid) to a BLACK+DECKER owned or authorized Service
Center for repair or replacement at BLACK+DECKER's
option. Proof of purchase may be required. BLACK+DECKER
owned and authorized service centers are listed online at
www.blackanddecker.com. This warranty does not apply to
accessories. This warranty gives you specific legal rights and
you may have other rights which vary from state to state
or province to province. Should you have any questions,
contact the manager of your nearest BLACK+DECKER
Service Center. This product is not intended for commercial
English
9
Publicité
Table des Matières
