KitchenAid KDTM354EBS Mode D'emploi page 11

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

OPTION SELECTIONS
OPTIONS
Sanitizes dishes and glassware in
accordance with NSF International NSF/
ANSI Standard 184 for Residential
Dishwashers. Certified residential
dishwashers are not intended for licensed
food establishments. Only sanitizing
cycles have been designed to meet the
requirements of the NSF/ANSI 184
performance standard for soil removal
and for sanitization efficacy. There is no
intention, either directly or indirectly, that
all cycles on a NSF/ANSI 184 certified
dishwasher meet the NSF/ANSI 184
performance standard for soil removal
and for sanitization efficacy.
The Sani indicator glows at the end of the
cycle if the Sani Rinse option was
successfully completed. If the indicator
does not activate, it is probably due to the
cycle being interrupted.
(on some models) For added
convenience, use for washing a small
load of dishes in the top rack to help keep
the kitchen continuously clean.
Runs the dishwasher at a later time or
during off-peak electrical hours. Select a
wash cycle and options. Press the Delay
button. Press START/RESUME. Close
the door firmly.
or (on some
NOTE: Anytime the door is opened (such
models)
as, to add a dish), the Start/Resume
button must be pressed again to resume
the delay countdown.
IMPORTANT: Control lock button varies by model. Your model may require you to press and hold PROSCRUB UPPER,
4 HOUR DELAY or BOTTLE WASH to lock the controls. The Control Lock light will turn on when the Control Lock
is active.
Use Control lock to avoid unintended use of the dishwasher between cycles, or cycle and option changes during
a cycle.
To turn on Lock, press and hold the control lock button designated for your model for 3 seconds. The Control Lock light
will stay on for a short time, indicating that it is activated, and all buttons are disabled. If you press any button while your
dishwasher is locked, the light flashes 3 times. The dishwasher door can still be opened/closed while the controls
are locked.
NOTE: You may need to disable Sleep Mode by pressing either Start/Resume or Cancel, or by opening and closing the
door before you are able to turn Control Lock off.
To turn off Control Lock, press and hold the control lock button designated for your model for 3 seconds. The light
turns off.
***Cycle times may increase depending on water temperature, heavy soil condition, and options selected. Adding options will add time to
the cycle. See the options information.
CONTROLS AND CYCLE STATUS
CONTROL
PURPOSE
To start or resume a
wash cycle
CAN BE
SELECTED
WITH
ProWash™
Tough
Normal
Top Rack Only
Available with
any cycle
Available with
any cycle
COMMENTS
If the door is opened during a cycle for any reason or if the power is interrupted, the
Start/Resume indicator flashes. The cycle will not resume until the Start/Resume button
is pressed and the door is closed.
NOTE: (for models with controls on top of the door) Push door firmly closed within 3
seconds of pressing Start/Resume. If the door is not closed within 3 seconds, the Start/
Resume light will flash, an audible tone will be heard, and the cycle will not start.
WHAT IT DOES
ADDED TIME TO
MIN
Increases the main
:10
wash temperature
from 105°F to 140°F
(41°C to 60°C) and
the final rinse from
140°F to 155°F (60°C
to 68°C).
Slightly faster wash
-:03
for smaller loads
Delays the start of a
1:00
cycle to the specified
.
time
ADDED
CYCLE***
WATER
(HH:MM)
GALLONS
(LITERS)
MAX
:50
0 - 1.5
(0 - 5.7)
-:08
0
24:00
0
11

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Kdtm404ebs1Kdtm384ebs

Table des Matières