Installation; General - Hatco SAL Série Manuel D'installation Et D'utilisation

INSTALLATION

General

Hatco Salamanders are shipped with most components pre-
assembled. Care should be taken when unpacking the shipping
carton to avoid damage to the unit and the components enclosed.
The salamander can be placed on a countertop or mounted to
an appropriate wall surface. The following installation instructions
must be performed before operating the salamander.
WARNING
ELECTRIC ShOCK hAzARD:
• Plug unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. If
plug and receptacle do not match, contact a qualified
electrician to determine and install the proper voltage
and size electrical receptacle.
• Unit must be installed by a qualified electrician.
Installation must conform to all local electrical codes.
Installation by unqualified personnel will void unit
warranty and may lead to electric shock or burn, as well
as damage to unit and/or its surroundings.
• Unit is not weatherproof. Locate unit indoors where
ambient air temperature is a minimum of 70°F (21°C)
and a maximum of 113°F (45°C).
FIRE hAzARD:
• To reduce the risk of fire, the appliance is to be installed
in non-combustible surroundings only, with no
combustible material within 18" (46 cm) of the sides,
front, or rear of the appliance or within 40" (102 cm)
above the appliance. The appliance is to be mounted on
floors of non-combustible construction with non-
combustible flooring and surface finish and with no
combustible material against the underside, or on non-
combustible slabs or arches that have no combustible
material against the underside. Such construction shall
in all cases extend not less than 12" (30 cm) beyond the
equipment on all sides.
• Locate unit a minimum of 2" (51 mm) from any walls. If
safe distances are not maintained, discoloration or
combustion could occur.
• Do not obstruct air intake openings or air exhaust
openings on outer housing of unit. Unit combustion or
malfunction may occur.
For wall mounting, use special wall mount bracket provided
with unit only. Secure wall mount bracket to a solid, non-
combustible surface using appropriate hardware for
mounting surface and weight of unit.
Locate unit at proper counter height in an area that is
convenient for use. Location should be level to prevent unit
or its contents from falling accidentally and strong enough
to support the weight of the unit and contents.
Do not place anything on top of unit; doing so may subject
personnel to injury or damage unit.
NOTE: A qualified person must check possible placements of
the salamander to ensure that the proper electrical
supply line is available.
1. Remove the unit from the shipping carton.
NOTE: To prevent delay in obtaining warranty coverage, complete
online warranty registration. See the ImPORTaNT
OWNER INFORmaTION section for details.
CAUTION
2. Remove tape and protective packaging from all surfaces
of unit.
3. Clean the unit thoroughly to remove all protective industrial
grease. NOTICE Use non-abrasive cleaners and cloths
only.
4. Remove the transport locking screw used to secure the
upper housing during shipping. Discard the screw.
Transport locking Screw
NOTE: Do not plug in or hardwire the unit until either
countertop installation or wall mounting is complete.
Do not install unit above grills, fryers, or other appliances
that will expose unit to high temperature, excessive
moisture, or grease-laden air. Improper installation will void
warranty.
5. For wall mounting, refer to the "Installing a Wall-mounted
Unit" procedure in this section.
Do not lay unit on the side with the control panel or damage
to unit could occur.
6. For countertop installation, install the 4" legs.
NOTE: Additional help may be needed to maneuver the unit to
the proper position for installing legs.
a. Carefully position the unit with the control panel facing
up.
b. attach the four legs by turning the legs clockwise into
one of the threaded holes in each of the four corners on
the bottom of the unit. Tighten the legs securely.
c. Return the unit to the upright position.
7. Place the unit in the desired location.
• locate the unit directly underneath an exhaust hood if
possible. This will ensure total suction of steam produced
during cooking.
• make sure the unit is installed where the ambient air
temperature will not rise above 113°F (45°C) and where
it will not be exposed to excessive moisture or grease-
laden air.
• make sure the unit is at the proper height in an area
convenient for use.
• make sure the countertop is level and strong enough to
support the weight of the unit and food product.
• make sure all the feet on the bottom of the unit are
positioned securely on the countertop with a minimum of
2" (51 mm) between the unit and any wall.
6
English
Transport Locking
Screw
NOTICE
NOTICE
Form No. Salm-0915