Additional Information; Troubleshooting; Power Supply; Audio Output - PIONEER DJ XDJ-RX2 Mode D'emploi

Additional information

Troubleshooting

! Improper operation is often mistaken for trouble or a malfunction that occurred in the device. If something is wrong with this unit, check the follow-
ing issues, and also access the following Pioneer DJ support site and check [FAQ] for [XDJ-RX2].
pioneerdj.com/support/
Some problems occurs due to the connected components. If the problem cannot be resolved after checking the connected components, ask the
service center or dealer for repairs.
! The unit may not operate properly due to static electricity or other external influences. If this happens, normal operation can be sometimes restored
by removing the power cord after turning the power off, and turning the power back on after inserting the power cord into the power outlet.

Power supply

Problem
The unit does not turn on.
The indicators do not light up.
The power suddenly turns off.

Audio output

Problem
Sound is not output, or sound is too
small.
Sound is distorted.
Sound is not output, or the output
sound is distorted or noisy.
Microphone sound is not output or
the volume is low.
Sound is distorted when an analog
player is connected to the [PHONO]
terminals of this unit.
Or, lighting of the channel level
indicator does not change when the
[TRIM] control is turned.
Display
Problem
Playing address is not displayed in the
remaining time display.
The category is not displayed.
The scale is not displayed.
The enlarged waveform is not
displayed.
Check
Is the power cord properly connected?
Is the [u] switch turned on?
Is the auto standby function activated?
(When auto standby is functioning, the
[MASTER REC (WAKE UP)] button is lit in red.)
Check
Are the [DECK 1, LINE1, PHONO1] and [DECK 2,
LINE2, PHONO2] selector switches set to the
proper positions?
Are the [TRIM] control, channel faders, crossfader
and [MASTER LEVEL] control set to the proper
positions?
Is the [MASTER LEVEL] control set to the proper
position?
Is the [TRIM] control set to the proper position?
Is the level of sound input to the [MIC] terminal set
to an appropriate level?
Is this unit placed near a TV?
Is the [MIC1, 2 LEVEL] control set to the proper
position?
Is the switch on this unit or the microphone
turned off?
Is an analog player with a built-in phono equalizer
connected to this unit?
Is an audio interface for computers connected
between the analog player and this unit?
Check
—
Is the rekordbox library information stored on the
USB device?
Is the USB device write-protected?
Is the track over 15 minutes long?
Is the track over 60 minutes long?
Remedy
Connect the power cord to an AC outlet. (page 10 )
Turn on the [u] switch.
This unit is shipped with the auto standby function set to on. If you do not
want to use the auto standby function, set [AUTO STANDBY] to [OFF] on the
[UTILITY] screen.
Remedy
Change the input source for the channel using the [DECK 1, LINE1, PHONO1]
and [DECK 2, LINE2, PHONO2] selector switches. (page 13 )
Set the [TRIM] control, channel faders, crossfader and [MASTER LEVEL] control
to the proper positions. (page 13 )
Adjust the [MASTER LEVEL] control so that the master channel level indicator
lights around [0 dB] at the peak level.
Set [ATT.] of [MASTER OUT] on the [UTILITY] screen to [-6 dB] or [-12 dB].
Adjust the [TRIM] control to confirm that the channel level indicator lights up in
orange at the highest volume. (page 13 )
Set the [MIC1, 2 LEVEL] control to the proper position.
Turn the TV off, or place this unit farther away from the TV.
Set the [MIC1, 2 LEVEL] control to the proper position.
Turn the switch on.
When using an analog player with a built-in phono equalizer, connect it to the
[LINE] input terminals. (page 10 )
If the analog player with a built-in phono equalizer has a LINE, PHONO selector
switch, set it to PHONO.
If the audio interface for computers has a line level output, connect it to the
[LINE] input terminals. (page 10 )
If the analog player has a LINE, PHONO selector switch, set it to PHONO.
Remedy
Playing address may not be displayed for files recorded in VBR. This happens
when it takes time for the unit to detect the length of the track and display the
playing address.
Use a USB device containing the library information that is exported from
rekordbox to the device..
Disable write-protection on the USB device to make it writable.
The scale is not displayed for tracks whose playing time is over 15 minutes.
The enlarged waveform is not displayed for tracks whose playing time is over 60
minutes.
15
En