Cycle Option Buttons; Delay Start; Nd Rinse; Stain Treat - Kenmore 796.4002 Série Guide D'utilisation Et D'entretien

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

CYCLE OPTION BUTTONS

Your washing machine features several additional cycle
options to customize cycles to meet your individual needs.
1
Turn on the washer and turn the cycle selector knob to
select the desired cycle.
2
Use the cycle modifier buttons to adjust the settings for
that cycle.
3
Press the cycle option button(s) for the option(s) you
would like to add. The button will light when that option
is selected.
If the selected option is not allowed for the selected
cycle, the chime will sound twice to inform you that it is
not allowed.
4
Press the START/PAUSE button to start the cycle. The
washer will start automatically after a brief delay for
locking the door.
NOTE: To protect your garments, not every option is
available with every cycle. See the CYCLE GUIDE on page
14 for details.
NOTE: If the START/PAUSE button is not pressed within 4
minutes, the control will shut off and the settings will be lost.

DELAY START

Once you have selected the cycle and other
settings, press this button to delay the start
of the wash cycle. Each press of the button
increases the delay time by one hour, for up
to 19 hours. Once the desired delay time is
set, press the START/PAUSE button to start the delay time.
nd
2
RINSE
This option will add an extra rinse to the
selected cycle. Use this option to help
ensure the removal of detergent or bleach
residue from fabrics.

STAIN TREAT

Use this option for heavily soiled loads that
need improved stain treatment. When
STAIN TREAT is selected, the water
temperature for the selected cycle will begin
as warm water to help prevent the setting of
certain types of stains. Then as the cycle progresses, the
water will be heated to higher temperatures to help remove
stains that require treatment at higher temperatures. This
option is designed for optimum stain removal.
NOTE:
• If STAIN TREAT is selected with the SANITIZE cycle, the
cycle will begin with very hot water since that is default for
that cycle and cannot be changed.
HOW TO USE

AUTO SOAK

1
Add detergent only to the Main wash compartment of
the dispenser drawer. (See "Using the Dispenser" on
pages 16-17.)
2
Select desired cycle.
3
Select cycle modifiers.
4
Press the START/PAUSE.

SPECIAL FUNCTIONS

CONTROL LOCK

turned OFF before the controls can be used. Once the
washer has shut off, the power button will allow the machine
to be turned ON, but the controls will still be locked. When
the controls are locked, "CL" will be displayed alternately
with the estimated time remaining.
Press and hold the CONTROL LOCK button for 5 seconds
to activate or deactivate the controls.

CLEAN WASHER

cleaner designed specifically for cleaning front load washers.
The CLEAN WASHER cycle should be run once a month, or
more often under heavy use conditions or if odor is present.
1
Turn ON the washer and press the CLEAN WASHER
button. Selecting any other cycle after CLEAN WASHER
has been selected will cause the CLEAN WASHER
cycle to be cancelled.
2
Fill the bleach dispenser to the MAX line with liquid
chlorine bleach. Do not overfill the bleach dispenser.
Overfilling will cause the bleach to be dispensed
immediately.
3
Press the START/PAUSE to start the cycle.
4
After the cycle has ended, open the door and allow the
drum interior to dry completely.
NOTE: Do NOT use this cycle with clothes, and do NOT
add detergent or fabric softener.
* For powdered tub cleaners, add the cleaner to the main
wash compartment of the dispenser drawer. Place tablet
cleaners directly into the tub. Always follow the cleaner
manufacturers instructions and recommendations.
20
Use the AUTO SOAK option to presoak
garments to help remove difficult spots or
stains on fabrics. This option provides a 30
minute presoak prior to the start of the
selected cycle.
Use this option to disable the controls. The
washer can be locked during a cycle. This
feature allows you to prevent children from
changing cycles or operating the machine.
Once set, the CONTROL LOCK must be
A buildup of detergent residue can occur in
the wash tub over time and can lead to a
mildewy or musty smell. The CLEAN
WASHER cycle is specially designed to
remove this buildup using bleach or other

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

796.4014 série

Table des Matières