Black & Decker FSMH1321 Mode D'emploi page 9

Attaching accessories (Fig H)
Align the lugs on the steam nozzle (17) with the recesses
u
on the accessory.
Press the accessory onto the steam nozzle (17) and twist
u
anti-clockwise until the accessory clicks into place.
Important! All accessories, apart from the SteaMitt
which has its own hose and connector (26), must be attached
to the steam hose (16) for use.
Removing the hose and accessories
Warning! The steam hose (16), Steam nozzle (17) and
accessories become hot during use. Allow the unit and all
accessories to cool before attempting to remove.
Removing an accessory
Twist the accessory clockwise then pull away from the
u
hose (16).
Removing the hose
Press the steam hose release button (16a) on the steam
u
hose (16) and pull away from the hand held steam unit.
SteaMitt
TM
Your BLACK+DECKER SteaMitt
TM
sanitising and cleaning tiles, work tops, kitchen surfaces and
bathroom surfaces. This appliance is intended for indoor
household use only.
Attaching the SteaMitt
steam unit
Warning! Inspect the seal between the connection point on
the hand held steam cleaner (5) and the SteaMitt
(26) before each use. If the seal malfunctions or is damaged,
please contact your nearest authorised repair agent. Do not
use the appliance.
Press the SteaMitt hose release button on the SteaMitt
TM
u
hose (26).
Connect the SteaMitt
TM
u
cleaner (5) and release the SteaMitt
making sure it clicks into place.
Important! Ensure that the SteaMitt
connected to the hand held steam cleaner (5).
If steam escapes from the joint, the hose is incorrectly fitted.
Switch off, allow the unit to cool then remove and refit the
hose.
Fitting a cleaning pad to the
Fit the cleaning pad (27) to the SteaMitt
u
attaching the 'loop' velcro strips (27a) on the upper side
of the cleaning pad, to the 'hook' velcro pads (25a) on the
underside of the SteaMitt
Warning! The SteaMitt
should not be used without fitting a
TM
cleaning pad.
(25)
TM
has been designed for
TM
hose to the hand held
TM
hose
TM
hose (26) to the hand held steam
hose release button
TM
hose (26) is securely
TM
SteaMitt
TM (Fig. L)
(25) by
TM
(4). Press down firmly.
TM
(Original instructions)
Note: The SteaMitt
TM
of varying thickness. The thinnest can be used for cleaning 3D
forms such as taps etc. The thicker versions can be used for
larger flat areas.
@
Warning! Always use the SteaMitt
figure M, with your hand inside the protective glove.
Warning! Never attempt to use the SteaMitt
@
gripping it externally as shown in figure N.
This will result in scalding.
@
Warning! Avoid using the SteaMitt
as shown in figure O.
Warning! Should a problem occur during use,
@
use the quick release tab to quickly remove the
SteaMitt from your hand as shown in figure P.
TM
Warning! Do not use the SteaMitt
@
such as windows as damage may be caused by the
sudden change in temperature.
@ Warning! Never point or direct the mitt at yourself
or any other person.
Note:
Variable steam dial is disconnected when the
SteaMitt is fitted and subsequently the flow of steam is
TM
limited.
Use
Important! This unit will kill 99.9% of bacteria and germs
when used in accordance with the instructions in this manual
and with the micro fibre pads fitted and a continuous run time
of 90 seconds.
Switching on and off
To switch the appliance on, press the ON/Off switch (1).
u
It takes approximately 15 seconds for the steam mop to
heat up.
TM
To switch the appliance off, press the ON/Off switch (1).
u
Note: always have your hand inside the SteaMitt
press the steam button.
Caution! Never leave the steam mop in one spot on any
surface for any period of time.
Always place the steam mop with the handle (8) supported in
the upright position when stationary and make sure the steam
mop is turned off when not in use.
Caution! Always empty the steam mop after use.
Note! When first filled or after running dry, it can take up to 45
seconds for steam to be produced.
Autoselect Technology (Fig. R)
TM
This steam mop is fitted with an Autoselect
shows various cleaning applications. They are used to select
the correct operating mode for your particular cleaning
operation.
ENGLISH
accommodates 3 types of cleaning pads
as shown in
TM
in tight corners
TM
on cold glass,
TM
TM
dial (2) which
TM
by
TM
before you
9