Publicité
614989-00, D51321
3/19/04
5:45 PM
Page 6
Fig. 10
Compressor will be sufficient for tools at all production rates.
Le compresseur peut actionner tout outil, quel que soit le taux de production.
El compresor será suficiente para las herramientas a todo índice de producción.
Compressor will be sufficient at slow or moderate production rates, but may have difficulty at very rapid rates.
Le compresseur peut actionner des outils à des taux de production faibles ou modérés, mais peut avoir de la difficulté à
des taux très élevés.
El compresor será suficiente a índices de producción lentos o moderados pero tendrá dificultad con índices demasiado rápidos.
Compressor will be adequate only when tools are utilized at slow production rates. (punch-out or occasional use)
Le compresseur ne sera vraiment efficace que lorsque les outils sont utilisés à de faibles taux de production (p. ex., lors de
travaux rapides ou occasionnels).
El compresor será adecuado sólo cuando las herramientas sean utilizadas a índices de producción lentos (perforación o uso
ocasional).
Not Recommended
Taux non recommandés
No se recomienda
5.5 HP Gas
8 HP Gas
Portable
14 - 16
2 HP Elec.
Handcarry
CFM
8 - 9 CFM
3.2 - 4 CFM
Outil à gaz
Outil à gaz
(5,5 hp)
(8 hp)
Outil élec-
23,8 – 27,2
Petit
trique
CMM
outil
(2 hp)
(14 – 16
portatif
CFM)
13,6 – 15,3
5,4 – 6,8 CMM
CMM
(3,2 – 4 CFM)
(8 - 9 CFM)
8 HP Gas
5,5 HP Gas
23,8 – 27,2
CMM
2 HP Elec.
Portátil
(14 – 16
13,6 – 15,3
5,4 – 6,8 CMM
CFM)
CMM
(3,2 – 4 CFM)
(8 - 9 CFM)
1
2
3
4
5
6
7
8+
MANY COMMON PROBLEMS CAN BE SOLVED EASILY BY UTILIZING THE CHART BELOW. FOR MORE SERIOUS OR PERSISTENT PROBLEMS,
Trigger valve housing leaks
O-ring or valve stem failure
Top cap leaks air
Loose cap screws
Damaged or worn gasket or O-ring
Exhaust leaks
Main seal or O-ring damaged, debris in tool.
Air leaks around nose when
Damaged or worn O-rings
tool is at rest. (Driver blade in up position)
Air leaks around nose when tool is in
actuated position. (Driver blade in
Damaged or worn bumper
down position)
Tool does not cycle in cold weather
Tool not receiving air
Valve may be frozen
Damaged or worn O-rings
Broken or damaged driver blade
Lack of power; sluggish
Low air pressure
Lack of lubrication
Damaged or worn O-rings
Exhaust port blocked or clogged
Skipping nails; intermittent feed
Air restricted
Lack of lubrication
Nose piece screws loose
Wrong size/angle fasteners
Dirty canister
Worn canister
Broken or damaged driver blade
Trigger valve O-ring worn or damaged
Worn piston O-ring
Worn or damaged check pawl and/or feed pawl
Canister loose
Nail platform at incorrect setting
Feed piston O-ring worn or damaged
Fasteners jam in tool
Driver channel in nose piece worn
Wrong size/ angle fasteners
Canister loose
Worn driver blade
Nose piece screws loose
Nails not feeding properly
Industrial
23+ CFM
Outil indus-
D51321 COIL ROOFING NAILER
triel
39,1+ CMM
CARACTÉRISTIQUES DES CLOUS
(23+ CFM)
D51321 CLOUEUSE À BOBINE POUR TOITURES
ESPECIFICACIONES DE LOS CLAVOS
Industrial
D51321 CLAVADORA PARA TECHADO EN ROLLO
39,1+ CMM
(23+ CFM)
Nail Lengths
Longueur
Largo de clavos
Shank Diameters
Diamètre de tige
Diámetro del vástago
Nail Coil Angle
Angle de la bobine
Ángulo del rollo de clavos
CARACTÉRISTIQUES DE L'OUTIL
D51321 CLOUEUSE À BOBINE POUR TOITURES
ESPECIFICACIONES DE LA HERRAMIENTA
D51321 CLAVADORA PARA TECHADO EN ROLLO
Height / Hauteur / Altura
Width / Largeur / Ancho
Length / Longueur / Largo
Weight / Poids / Peso
Recommended Operating Pressure
Pression d'utilisation recommandée
Presión de operación recomendada
Air Consumption per 100 cycles
Consommation d'air par 100 cycles
Consumo de aire por cada 100 ciclos
Loading capacity
Capacité de charge
Capacidad de carga
Troubleshooting Guide
CONTACT A D
WALT SERVICE CENTER OR CALL 1-(800)-4-DEWALT.
E
DISCONNECT AIR FROM TOOL BEFORE ALL REPAIRS
Replace valve using: Trigger Valve Kit: Cat. # D510005
Tighten cap screws using appropriate Allen wrench
Replace gasket/O-rings using: O-ring Repair Kit, Cat. # D513211
Replace gasket/O-rings using: O-ring Repair Kit, Cat. # D513211
Replace gasket/O-rings using: O-ring Repair Kit, Cat. # D513211
Replace bumper using: Bumper Kit, Cat. # D513213
Check air supply
Warm up tool
Replace gasket/O-rings using: O-ring Repair Kit, Cat. # D513211
Replace Driver Blade Kit: Cat. # D513212
Check air supply
Lubricate tool using approved pneumatic tool oil.
Replace gasket/O-rings using: O-ring Repair Kit, Cat # D513211
Disconnect air, remove exhaust plate from top of tool, clean port
Check air supply and couplers
Lubricate tool using approved pneumatic tool oil
Tighten nosepiece screws using appropriate allen wrench
Use only recommended fasteners
Clean canister track and nosepiece
Replace canister
Replace Driver Blade Kit; Cat. # D513212
Replace valve using: Trigger Valve Kit; Cat. # D510005
Replace Piston O-Ring using: O-Ring Repair Kit, Cat.# D513211
Replace check pawl and/or feed pawl
Check that canister latch is holding firmly
Set nail platform to proper nail setting
Replace feed piston O-ring using: O-Ring Repair Kit, Cat. # D513211
Replace nosepiece
Use only recommended fasteners
Check that canister screws are holding firmly
Replace Driver Blade Kit; Cat # D513212
Tighten nosepiece screws using appropriate Allen wrench
Ensure nails are feeding properly into nose.
NAIL SPECIFICATIONS
.75'' - 1.75''
20 – 40 mm (0,75 – 1,75 po.)
20 – 40 mm (0,75 – 1,75 pulg.)
.120
3 mm (0,120 po.)
3 mm (0,120 pulg.)
15˚
15°
15˚
TOOL SPECIFICATIONS
D51321 COIL ROOFING NAILER
11.4'' (289,6 mm)
4.6" (118,1 mm)
10.6'' (269,7 mm)
4.90 lbs. (2,22 kg)
70 - 120 psig (4.9 - 8.3 bar, 5 to 8.5 kg/cm
2
2
de 5 à 8,5 kg/cm
(70 à 120 lb/po
ou 4,9 à 8,3 bar)
70 - 120 psi (4,9 – 8,3 bar, 5 a 8,5 kg/cm
4.15 scfm @ 100 psi
4,15 scfm à 100 psi (0,12 scmm a 6,9 bar)
4,15 scfm a 100 psi (0,12 scmm a 6,9 bar)
Up to 120 nails
Jusqu'à 120 clous
Hasta 120 clavos
2
)
2
)
Publicité
