Helpful Hints; Declaration Of Conformity - ThermoPro TP-15G Manuel D'utilisation

7. Press /°C/°F button to turn off the thermometer. This thermometer also comes with
auto-off feature: it will automatically turn off if no button has been pressed for 10 minutes.
EN
Calibration
The thermometer comes with a calibration feature. In most cases, the thermometer was
calibrated precisely at our manufacturing facility, and generally you do NOT need to calibrate
the thermometer. However, after a long period of use AND you believe that the temperature
reading displayed by the thermometer is not accurate, you may follow the process below to
re-calibrate the thermometer:
1. Use distilled or purified water to make ice cubes in your refrigerator;
2. Get a thermal insulated bottle. If you don't have one, use a beaker or a regular cup;
3. Fill the bottle with ice cubes (no less than 70% of the volume), then top off with cold
distilled or purified water (no greater than 30% of the volume);
4. Stir the mixture and let it sit for 10 minutes to allow the ice and water to reach its
temperature equilibration;
5. Turn on the thermometer and hold the HOLD/CAL button for 5 seconds to enter Calibration
mode. CAL will begin flashing for a few seconds and then the current temperature reading
will begin to flash which means the thermometer is in Calibration mode;
6. Immerse the probe in the ice/water mixture and make sure not to touch the sides of the
container. Wait till the temperature reading drops to its lowest value, which should be
around 32°F or 0°C. If the temperature of the ice/water mixture is not within 28°F to 36°F
(or -2°C to +2°C), the calibration can't be continued: you will need to follow the above
steps to re-make the ice/water mixture;
7. Hold the Hold/CAL button for 3 seconds to confirm the calibration and exit the Calibration
mode.
Note:
The Calibration mode will only last for 15 seconds. If you're unable to finish the calibration
within 15 seconds, the thermometer will automatically exit Calibration mode.
Undo-Calibration
If you want to undo the calibration and go back to the default calibration setting, please
follow the below steps:
1. Turn on the thermometer and hold the hold/CAL button for 5 seconds to enter Calibration
mode;
2. When you see temperature reading begins flashing, press and hold the Light button for 3
seconds. The temperature reading will stop flashing and the calibration is set to the
default setting.
-4-

Helpful hints

When measuring multiple or different foods and meats, it may be desirable to cool the
probe by rinsing the tip with cold water between readings.
It is recommended that you wipe the probe tip clean between readings. This is especially
important when taking readings from different foods and meats.
The thermometer is designed for temporary, hand held use. Do not use in an oven. Do not
leave inserted in extremely hot foods or liquids (anything over 572°F) for more than 1
minute.
Always take your reading in the thickest available portion of meat. Thin portions of meat
are difficult to measure because they tend to cook through fast. Avoid touching bone. If
the tip touches the bone or heavy fat area of the meat, or if the tip is not deep enough,
take a second reading to ensure accuracy.
Not intended for use by persons ages 12 or under.
Care of your thermometer
Do not touch the stainless portion of the thermometer during or right after measuring
temperatures since it will be hot.
Do not leave exposed to extreme high or low temperatures as this will damage electronic
parts and plastics.
Do not leave the thermometer inserted in food during cooking.
Remove battery if stored for more than four months.
Do not subject the unit to excessive force, shock, dust, temperature or humidity.
Do not immerse the unit in water.
Do not remove any screws.
Do not dispose this unit in a fire. IT MAY EXPLODE.
Keep unit away from children. The unit or parts of the unit might be a choking hazard.
Dispose of the unit legally and recycle when possible.

Declaration of Conformity

Hereby, the manufacturer declares that this product complies with the basic requirements
and applicable regulations of the EMC Directive 2014/30/EU. The complete declaration of
conformity can be found at:
https://itronicsmall.com/eu-declaration-of-conformity/
-5-
EN