Bosch GBH 180-LI Professional Notice Originale page 8

8 | English
(17) Battery charge indicator
(18) Universal holder with SDS plus shank
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Cordless rotary hammer
Article number
Rated voltage
Rated speed
– Clockwise
– Anticlockwise
A)
Impact rate
Impact energy per stroke ac-
cording to EPTA-Procedure
05:2016
Tool holder
Max. drilling diameter
B)
– Concrete
– Steel
– Wood
Weight according to EPTA-
A)
Procedure 01:2014
Permitted ambient temperat-
ure
– During charging
C)
– During operation and
during storage
Recommended batteries
Recommended chargers
A) Depends on battery in use
B) Optimum performance with driling diameter 6−10 mm
C) Limited performance at temperatures <0 °C
Assembly
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Battery Charging
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
1 609 92A 5JW | (19.11.2019)
A) Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
A)
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
GBH 180-LI
is discharged, the power tool is switched off by means of a
3 611 J11 1.. protective circuit: The application tool no longer rotates.
V= 18 u
-1
min 0−1800
Follow the instructions on correct disposal.
-1
min 0−1800
-1
min 0−5100
J 2
SDS-plus
Inserting and removing the battery (see figures
A1–A2)
mm 20
u
mm 13
mm 30
– Slide the battery (11) all the way into the battery bay.
kg 2.8−3.7
– To remove the battery (11), press the release but-
Battery Charge Indicator
°C 0 to +35
The green LEDs on the battery charge indicator (17) indic-
°C –20 to +50
ate the state of charge of the battery (11). For safety reas-
ons, it is only possible to check the state of charge when the
power tool is not in operation.
GBA 18V...
ProCORE18V
Press the battery charge indicator button (16) to show the
4.0A/8.0Ah
state of charge. This is also possible when the battery is re-
moved.
GAL 18...
GAX 18... If no LED lights up after pressing the battery charge indicator
button (16), the battery is defective and must be replaced.
GAL 36...
Battery model GBA 18V... (see figure B1)
LEDs
3× continuous green light
2× continuous green light
1× continuous green light
3× flashing green light
Battery model ProCORE18V... (see figure B2)
LEDs
5× continuous green light
4× continuous green light
3× continuous green light
2× continuous green light
1× continuous green light
Do not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
Bosch recommends using battery
packs with a capacity of at least 3.0
Ah.
Do not use force to insert the battery. The battery is de-
signed in such a way that it can only be inserted into the
power tool when it is in the right position.
ton (13) on the battery and pull it out of the battery bay.
Capacity
60−100 %
30−60 %
5−30 %
0−5 %
Capacity
80−100 %
60−80 %
40−60 %
20−40 %
5−20 %
Bosch Power Tools