Installation Notes - EINHELL RUBIN Instructions De Montage

Installation notes:

Page 14
24
Assembly of the plastic web panels on the
front wall
Important note: The outside of the plastic web
panels (with UV coating) is marked „Außenseite /
Outside" at the edge, and it is also the side onto
which the protective film has been stuck.
Only remove the protective film from the plastic web
panel you are currently installing.
Please check the exact length specifications for the
single and double clips and measure the lengths
before you install the clips.
24/a: U-profiles are attached to the undersides
of the two 600 x 1400 / 1728 mm plastic web panels
(items 9 and 10).
Page 15
Important note (Figure 24/c, bottom): Make sure
that the plastic web panels are positioned on the
crossmember so that they make contact in the way
shown in the illustration.
24/b: Now insert the plastic web panels into the front
wall. Slide the two larger plastic web panels from
below up against the crossmember and position them
on the floor profile. On the sides the plastic web
panels are held by the profiles which have already
been installed. The panels are fixed in step 24/d
by applying the clips.
24/c: The smaller triangular plastic web panels are
positioned on the crossmember and positioned
between the struts. The panels are fixed in step 24/d
by applying the clips.
Page 16
Figure 24/e: Profile diagram (single clip / door hinge)
Figure 24/f: Profile diagram (single clip / corner
profile)
Tip: Use a solid object (e.g. the handle of a
screwdriver) to lightly tap several times on the clips
and knock them from the top down into position.
Page 17
Figure 24/g: Profile diagram (double clip / roof strut)
24/h: Additionally secure the two larger plastic web
panels on the floor profile using the spacers. Secure
the spacers (positioned roughly in the middle of the
plastic web panel) on the floor profile using self-
drilling screws with tapping screw threads (item 5).
If necessary, pre-drill holes with the drill
(diameter: 2 mm).
4
ABA_RUBIN_Teil2_Titel+GB.pmd 4
Important note: Make sure that the wider side of the
spacers is attached to the floor profile. The narrow
side is used to fix the plastic web panel.
Page 18
25
Assembly of the plastic web panels on the
rear wall
Important note: The outside of the plastic web
panels (with UV coating) is marked „Außenseite /
Outside" at the edge, and it is also the side onto
which the protective film has been stuck.
Only remove the protective film from the plastic web
panel you are currently installing.
Please check the exact length specifications for the
single and double clips and measure the lengths
before you install the clips.
25/a: U-profiles are attached to the underside of the
600x1400/1721 mm plastic web panels (items 9 and
10) and the 600x1721mm plastic web panels (item 11).
Page 19
Important note (Figure 25/c, bottom): Make sure
that the plastic web panels are positioned on the
crossmember so that they make contact in the way
shown in the illustration.
25/b: Now insert the plastic web panels into the rear
wall. Slide the slanted plastic web panels from below
up against the crossmember and position them on
the floor profile. On the sides the plastic web panels
are held by the profiles which have already been
installed.
25/c: The smaller triangular plastic web panels are
positioned on the crossmember and positioned
between the struts. Afterwards, position the two
rectangular plastic web panels between the floor
profile and the crossmember. The panels are fixed in
step 25/d by applying the clips.
Page 20
Figure 25/e: Profile diagram (single clip / corner
profile)
Figure 25/f: Profile diagram (double clip / roof and
side strut)
Tip: Use a solid object (e.g. the handle of a
screwdriver) to lightly tap several times on the clips
and knock them from the top down into position.
07.04.2006, 09:48