Signal Input - Harman JBL DSP4086 Mode D'emploi

Signal input

• Line-level inputs: If your source unit offers preamp outputs,
connect the front outputs to inputs 1 and 2 on the amplifier, the
rear outputs to inputs 3 and 4, and the subwoofer outputs to
inputs 5 and 6 using RCA patch cables.
Note: when using low-level signals and remote turn-on lead, set
the "Turn-on Mode" switch to "REM" and the "Input Level" switch to
"LO".
1
2
EN
3
4
5
6
• High-level inputs: If your audio system's source unit does
not have line-level outputs, use the supplied high-level input
adapters to connect to the speaker output wires of your source
unit to the RCA inputs of the amplifier. The 12-volt DC offset
feature will turn the amplifier on when it senses signal.
NOTE: You can connect the wires from as many as six of your
vehicle's speakers to the amplifier. For example, these can include
front left and right tweeters to inputs 1 and 2, front left and right
woofers to inputs 3 and 4, and rear left and right full-range speakers
to inputs 5 and 6. The signals from each of these speakers can be
summed to create a full-range output, if necessary, and assigned to
any of the amplifier output wires. See "Setting the Sound" for more
details.
NOTE: When using high-level signals, set the "Turn-on Mode" switch
to "DC" (to turn on when it receives battery power) or "AUDIO" (to
turn on when it senses signal from your source unit), and the "Input
Level" switch to "HI". If no sound plays, change the "Input Level"
switch to "HI2".
Insert
Loosen
Screws Wires
1
2
3
4
5
6
Speaker Output Connections
Connect your speakers to the wires of the speaker output wiring
harness, observing proper polarity: connect each positive (+) lead
to the appropriate positive (+) speaker terminal, and negative (-)
lead to the appropriate negative (-) speaker terminal. Then plug the
speaker output wiring harness into the DSP Amplifier.
NOTE: You can connect up to 8 speakers to the JBL DSP Amplifier,
then specify the frequencies the amplifiers sends to each one with the
JBL tuning software. See "Setting the Sound" for details.
NOTE: If you decide you need more power in your system, you can
use two or more of the speaker output wires to connect one or more
additional amplifiers. Connect the desired number of speaker output
wires to the high-level inputs of the new amplifier(s). IMPORTANT: make
sure to adjust the output levels of the channels you are connecting to
the extra amplifier(s) to ensure that you do not overdrive the external
amplifier(s) and reduce noise, if present.
IMPORTANT: None of the speaker output channels can be bridged.
3
TURN-ON
MODE
REM DC AUDIO
INPUT
LEVEL
LO HI HI2
TURN-ON
MODE
REM DC AUDIO
Tighten
OR
Screws
TURN-ON
MODE
REM DC AUDIO
INPUT
LEVEL
LO HI HI2
AUDIO
SPEAKER OUTPUT CHANNELS
INPUT
1+ 2+ 3+ 4+ 5+ 6+ 7+
REMOTE
1- 2- 3-
4- 5-
INPUT
LEVEL
LO HI HI2
Wire color
White
White/Black
Gray
Gray/Black
Green
Green/Black
Purple
Purple/Black
Orange
Orange/Black
Blue
Blue/Black
Red
Red/Black
Yellow
Yellow/Black
Connecting the remote bass control
Plug the remote bass controller into the appropriate input on
the control panel of the DSP Amplifier. Mount the remote in a
convenient location, such as under the dash, using sheet metal
screws.
NOTE: The remote bass control is capable of controlling the subwoofer
output level from channel 7 or 8 when assigned as a "sub" channel.
This will allow adjustment of subwoofer level from -30dB to +6db in the
tuning software. It is not a bass boost control. We expect that you will
use the remote bass control from an external subwoofer amplifier should
you want to control bass boost.
POWER
8+ REM OUT GND 12V REM IN
PC
PRT
6- 7- 8-
GND 12V
PWR
TURN-ON GND 12V
MODE
REM DC AUDIO
To speakers
Channel designation
Channel 1 +
Channel 1 –
Channel 2 +
Channel 2 –
Channel 3 +
Channel 3 –
Channel 4 +
Channel 4 –
Channel 5 +
Channel 5 –
Channel 6 +
Channel 6 –
Channel 7 +
Channel 7 –
Channel 8 +
Channel 8 –