Use; Weighing Function; Saving Personal Data; Measurement And Analysis - AEG PW 5570 FA Mode D'emploi

English
38

Use

Use the SET, UNIT, (UP) and
change the stored settings.
NOTE:
The scales are factory set with the units "kg" and "cm".
To change the settings to "lb" or "st" as well as "Ft:in",
proceed as follows:
• Switch the scales on by applying gentle pressure to the
surface with your foot or toe.
• Press the UNIT button until the desired unit of weight
is displayed. The unit for the height also automatically
changes.

Weighing Function

• Place the scale on a hard, flat surface (avoid carpets). An
uneven floor contributes to inaccurate measurements.
• Stand on the scales with both feet. The device switches
on automatically.
• Distribute your weight equally and wait for the scale to
determine your weight.
• The digits on the display will flash before your exact
weight will be shown.
• In order to extend the battery life, the device will auto-
matically turn off 10 seconds after you have stepped off
the scale.

Saving Personal Data

NOTE:
• The scale has default values that you can change, as
described below.
• Carry out the following steps in sequence and within a
few seconds. Otherwise, the device will automatically
cancel input mode.
• Press the button SET. The memory space will flash on the
display (USER). Confirm the setting by pressing SET or se-
lect another memory space by pressing the UP / DOWN
button. Then press SET to go to the next setting.
• The symbol for "male" or "female" will flash. Confirm the
setting by pressing SET or use the UP / DOWN button to
choose the symbol for your gender. Then press SET to go
to the next setting.
• The height setting will flash. Select your height by press-
ing UP or DOWN button. Holding down one of the
buttons will accelerate the process. Confirm your entry by
pressing SET.
• The setting AGE will flash. Select your age by pressing UP
or DOWN button. Holding down one of the buttons will
ac-celerate the process. Confirm your entry by pressing
SET.
• The default symbol for the "unathletic" type flashes.
Which type do you consider yourself to be? Select your
(DOWN) buttons to
type using the UP or DOWN button: "unathletic", "aver-
age" or "athletic". Confirm your selection with SET.
• If only the stored position and the display 0.0 kg
(0.0 lb/0:0 st) is still shown, input mode for this stored
position is completed.
You now have the following options:
• You can change the units for weight and type. Press the
UNIT button until the desired unit of weight is displayed.
The unit for the height automatically changes.
• Press the SET button to see the selected settings again.
• Allocate further memory spaces. There are 10 spaces
avail-able in total. Press SET and change the space by
pressing the UP or DOWN button. Proceed further as
described above.
• If you want to make changes, press SET (USER flashes).
Select the stored position using the UP or DOWN but-
ton. Proceed further as described above.
• You can immediately start measuring.

Measurement and Analysis

Record your personal data in the memory.
NOTE:
• The device can only function correctly if you stand on
the device with bare, dry feet!
• If necessary wipe the contact surfaces to improve
results.
• Due to the significant fluctuation of body fat, it is
difficult to attain a standard value. On average the
optimal testing time is between 6 p.m. and 8 p.m, since
the body fat remains very consistent during this period
of time.
• Press the SET button. The preset stored position data ap-
pears on the display (USER flashes). Use the UP / DOWN
button to select the stored position at which your data is
saved.
• Wait for the USER display and 0. 0 kg (0.0 lb/st) to stop
flashing.
• Stand on the contact surfaces (4) of the scales with both
feet.
• Firstly your weight will flash on the display.
• After a few seconds, the following results will be shown:
1. - the body fat content in % (
- the body water content in % (
- the results analysis in the form of a bar
2. - the muscle mass content in % (
- the bone mass content in % (
- the calorie requirement per day
3. - The preset gender
- The preset type
- The preset height
- The preset age (AGE)
- The weight gain (INCREASE) / the weight loss
(DNCREASE) in kg (lb/st) in comparison to the previ-
ous measurement
symbol)
symbol)
symbol)
symbol)