Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
8.5.6 Drehen kurzer Kegel mit dem Oberschlitten .....................................................31
8.5.7 Gewindedrehen ............................................................................................31
9
10 WARTUNG
10.1.1
Abschmieren ...........................................................................................32
10.1.2
Backen auswechseln .................................................................................33
11 LAGERUNG
14.1
Anzeige- und Bedienelemente ....................................................................... 35
14.2
Technische Daten / Technical Data ............................................................... 35
14.3
Grundlegende Funktionen ............................................................................. 36
14.3.1
Nullsetzen und Datenwiederherstellung .......................................................36
14.3.2
ABS/INC Modus .......................................................................................36
14.3.3
Koordinateneingabe .................................................................................36
14.3.4
Halbierungsfunktion (1/2 Funktion) ............................................................37
14.3.5
Anzeige Durchmesser/Radius.....................................................................37
14.3.6
Y+Z Funktion (anwendbar nur bei 3-Achs-Drehmaschinen) ...........................37
14.3.7
Memory-Funktion .....................................................................................37
14.3.8
Lineare Fehlerkompensation ......................................................................37
14.4
Systemparameter einstellen .......................................................................... 38
14.4.1
Gebertyp auswählen .................................................................................38
14.4.2
Auflösung einstellen .................................................................................39
14.4.3
Auswahl der Zählrichtung ..........................................................................39
14.4.4
Zoll- und metrische Umrechnung ...............................................................40
14.4.5
14.4.6
DRO-Modus einstellen ...............................................................................40
14.4.7
Achsnummern einstellen ...........................................................................41
14.4.8
ID der Anzeigeeinheit überprüfen ...............................................................41
15 PREFACE (EN)
16.1
Intended Use of the Machine ......................................................................... 43
16.1.1
Technical Restrictions ...............................................................................43
16.1.2
Prohibited Applications / Hazardous Misapplications ......................................43
16.2
User Requirements ........................................................................................ 43
16.3
Safety Devices ............................................................................................... 44
16.4
General Safety Instructions .......................................................................... 44
16.5
Electrical Safety ............................................................................................ 45
16.6
Special Safety Instructions for Lathes ........................................................... 45
16.7
Hazard Warnings ........................................................................................... 45
18.1
Preparatory activities .................................................................................... 46
18.1.1
Checking Delivery Content ........................................................................46
18.1.2
Site Requirements ....................................................................................47
18.1.3
Surface Preparation ..................................................................................47
18.1.4
Fastening the Digital Read Out (only for model ED400FDDIG) .......................48
18.1.5
Aligning the Lathe ....................................................................................48
18.1.6
Checking the Jaw Chuck ...........................................................................48
18.1.7
Visual Inspection ......................................................................................49
18.2
Power Supply ................................................................................................ 50
19.1
Before Start-up ............................................................................................. 50
19.2
Retracting the Machine ................................................................................. 50
19.3
Operating Instructions .................................................................................. 50
19.4
Operation ...................................................................................................... 50
19.4.1
Starting / Stopping the Engine ...................................................................50
19.4.2
Selecting Spindle Speed Range ..................................................................50
19.4.3
Adjusting the Spindle Speed ......................................................................51
HOLZMANN MASCHINEN GmbH
www.holzmann-maschinen.at
INHALT /INDEX
31
32
33
33
34
35
42
43
46
46
50
3
ED400FD | ED400FDDIG
Publicité
Table des Matières
