Accessories; Cleaner Maintenance - Hoover H-POWER 700 Manuel D'utilisation

ACCESSORIES

To obtain the best performance and efficiency it is recommended that the correct nozzles
are used for the main cleaning operations. These nozzles are indicated in the diagrams
by the letters GP, HF or CA.
A nozzle type GP can be used to clean both carpet and hard floor.
A nozzle type HF is suitable for use only on hard
A nozzle of type CA is suitable for use only on carpet.
The other nozzles are accessories for specialist cleaning tasks and are recommended
for occasional use only.
All accessories can be fitted to the end of the handle* or the end of the telescopic tube*.
Accessory Set**:
Crevice Tool – For corners and hard to reach areas.
Furniture Nozzle – For soft furniture and fabrics.
Dusting Brush – For bookshelves, frames, keyboards and other delicate areas.
Dual Action Pet Hair Remover Nozzle* [W] – Use the mini turbo nozzle on stairs or for
deep cleaning on textile surfaces and other hard to clean areas. Particularly suitable for
pet hairs removal.
Dual Action Allergen Remover Nozzle* [X] – Use the mini turbo nozzle on stairs or for
deep cleaning on textile surfaces and other hard to clean areas, particularly suitable for
allergen removal.
Parquet Extra Care* [Y] – For parquet floors and other delicate floors.
Long 2in1 Tool* [V] – Crevice tool and dusting brush - It allows to clean hard-to-reach
areas such as bookshelves and high corners.
IMPORTANT: Do not use mini turbo nozzles on rugs with long fringes, animal hides and
carpet pile deeper than 15mm. Do not keep the nozzle stationary while brush is rotating.

CLEANER MAINTENANCE

Emptying the Dust Bin
When the dust reaches the max level indicator on the container, empty the dust bin.
IMPORTANT: To maintain optimum performance do not allow the dust exceed the max
level indicator.
Switch the cleaner off by pressing the On/Off button on the cleaner main body [8]
1.
or pressing the On/Off button on the hose handle [9], and unplug the power cable.
2. Lift the dust bin release handle and remove the dust bin assembly from the cleaner. [12]
3. Hold the dust bin with one hand and with the other hand press the dust bin flap
release button. [13]
4. Close the dust bin flap and refit the dust bin assembly to the cleaner main body.
Cleaning the washable filters
The cleaner is fitted with a blue filter pack. To maintain optimum cleaning
* Certain Models Only ** May vary according to model
floor.
performance regularly remove the filters and tap against the side of the bin to
release dust. The filters should be washed every 5 bin empties or when the filter
has excessive dust level.
IMPORTANT: All bagless cleaners require regular filter cleaning. Failure to
clean your filters may result in air blockage, overheating and product failure.
This may invalidate your guarantee.
IMPORTANT: Regularly check and maintain the filters.
IMPORTANT: Always ensure the filter pack is fully dry before use.
To access the pre-motor filter:
1. Lift the dust bin release handle and remove the dust bin assembly from the cleaner. [12]
2. Hold the dust bin with one hand and with the other hand lift the dust bin lid opening
latch to open the bin lid. [14]
Remove the pre-motor filter located in the bin lid. [16]
3.
4. Gently tap and wash the pre-motor filter. Do not use hot water or detergents. Remove
excess water from the filter and leave to dry fully before re-using. [19, 20]
5. Reassemble the pre-motor filter to the dust bin lid once fully dry and refit to the
cleaner.
To access the exhaust filter:
1. Unclip the exhaust filter cover from the rear of the cleaner main body. [17]
2. Remove the exhaust filter from the rear of the cleaner. [18]
3. Gently tap and wash the filter using warm water. Do not use hot water or detergents.
Remove excess water from the filter and leave to dry fully before re-using. [19, 20]
4. Refit the exhaust filter to the rear of the cleaner once fully dry and refit the exhaust
filter cover.
IMPORTANT: Do not use the product without the filter pack fitted.
Cleaning the dust bin / separation unit
This cleaner uses a separation system and shroud cleaning system unique to Hoover. If
necessary the separation unit can be disassembled from the dust bin and cleaned.
Lift the dust bin release handle and remove the dust bin assembly from the cleaner. [12]
1.
2. Hold the dust bin with one hand and with the other hand lift the dust bin lid opening
latch to open the dust bin lid. [14]
3. Remove the separation system (including the integrated shroud cleaning system)
from the dust bin. [15]
4. If necessary, use a cloth to remove excessive dust from the separation system
(including the integrated shroud cleaning system).
5. Place the dust bin under tap water. Rinse with lukewarm water. Wash internal
surfaces of the dust bin with water only. DO NOT use soap detergents to wash the
internals of the dust bin.
6. Reassemble the internal component to the dust bin, ensuring all components are dry.
7. Close over the dust bin lid and refit dust bin assembly to cleaner.
3
GB