Tool Settings; Settings Menu - Bosch GLM 120 C Professional Notice Originale

Continuous laser beam
If necessary, you can switch the measuring tool to continu-
ous laser beam operation. To do this, select the settings for
the measuring tool using the soft key (3) [
ton (4) [+] or the button (11) [–] to select the continuous
laser beam and confirm this by pressing the button (13)
[Func].
Do not direct the laser beam at persons or animals and
u
do not stare into the laser beam yourself (even from a
distance).
In this setting, the laser beam remains switched on even
between measurements; measurement simply requires one
brief press of the measuring button (2) [ ].
The continuous laser beam can be switched off again in the
settings or automatically when the measuring tool is
switched off.

Settings menu

To enter the settings menu (i), briefly press the soft key (3)
[ ] or press and hold the button (13) [Func].
Use the button (4) [+] or the button (11) [–] to select the
required setting and confirm this by pressing the button
(13) [Func]. Select the required setting.
To exit the settings menu, press the on/off/delete button (9)
[ ] or the soft key (12) [ ].
Settings
Bluetooth®
Reference level
Timer function
Continuous laser beam
Grade measurement calibration
Target indicator calibration
Internal memory (deleting and formatting)

Tool settings

Timer function
The timer function is useful when measuring in hard-to-reach
areas, for example, or when the measuring tool should be
kept stationary during measurement.
Select the timer function in the settings. Select the required
time period between triggering the timer and starting meas-
urement and confirm by pressing the measuring button (2)
[ ] or the button (13) [Func].
Then press the measuring button (2) [ ] to switch on the
laser beam and focus on the target. Press the measuring but-
ton (2) [ ] again to start the measurement. The measure-
ment will begin after the set time period has expired. The
measured value is displayed in the result line (a).
The time period between triggering the timer and starting
measurement is displayed in the status bar at the top.
Bosch Power Tools
Continuous measurement and minimum/maximum measure-
ment are not possible with the timer function enabled.
The timer remains enabled until the measuring tool is
]. Use the but- switched off or until the timer is switched off in the settings
menu.
Tool settings menu
Select the tool settings menu in the settings menu.
Use the button (4) [+] or the button (11) [–] to select the
required tool setting and confirm this by pressing the button
(13) [Func]. Select the required tool settings.
To exit the tool settings menu (o), press the on/off/delete
button (9) [ ] or the soft key (12) [
Tool settings
ft/m
Setting the language
Select the language option in the tool settings menu. Set the
required language and confirm this by pressing the button
(13) [Func].
Setting the date and time
Select the time & date option in the tool settings menu. Set
the date and time according to the instructions on the dis-
play and confirm these by pressing the soft key (12) [
Changing the unit of measurement
Select the unit of measurement option in the tool settings
menu. The default unit of measurement is m (metres).
Set the required unit of measurement and confirm this by
pressing the button (13) [Func].
To exit the menu item, press the on/off/delete button (9) [
] or the soft key (3) [
saved after you switch off the measuring tool.
Changing the unit of measurement of an angle
Select the option for setting the unit of measurement for
angles in the tool settings menu. The default unit of measure-
ment for an angle is ° (degrees).
Set the required unit of measurement for angles and confirm
this by pressing the button (13) [Func].
English | 27
].
Language
Time & date
Unit of measurement
Unit of measurement for angles
TrackMyTools
Tool information
Tone signals
Switch-off time
Dimmer
Display brightness
Display orientation
]. The selected tool settings remain
1 609 92A 4F4 | (22.10.2018)
].