Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
English
Attaching the Auxiliary Handle (Fig. A, C)
1. Place the auxiliary handle
base
17
so the upper powerhead pole
between them.
2. Hold the auxiliary handle in place and slide the handle
bolts
18
and washers into the handle from the top,
threading them into the handle base.
3. Tighten the handle bolts with the supplied hex wrench.
Ensure the handle is securely attached.
4. Repeat for the other side of the auxiliary handle.
Powerhead (Fig. B)
WARNING: To reduce risk of injury:
•
Before any use, be sure everyone using this product
reads and understands all safety instructions and
other information contained in the powerhead and
attachment manuals.
•
Never apply power without an attachment being
properly mounted to the powerhead.
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
The powerhead can separate from the attachment by
turning the knob
20
counterclockwise, depressing the
latching button
21
and gently pulling them apart by their
poles
1
,
19
.
This should only be done with the power switch off and the
battery pack removed. Inside the upper powerhead pole
is a mechanical coupling that will spin if the powerhead
is turned on. This coupling can cause injury if contacted
while the powerhead is operating. The arrows
align for proper assembly of most attachments. See specific
attachment instructions for details.
nOTE: Ensure the attachment is fully engaged and the
knob is fully tightened before operating. Check for proper
engagement and tightness during use.
Attachments
WARNING: This powerhead is only to be used with
DEWALT attachments. Use of attachments that are not
recommended for use may increase risk of injury.
WARNING: Read the entire instruction manual
for each optional attachment prior to using with
this powerhead.
This powerhead has been designed for the purpose of
residential lawn and garden maintenance. It is recommended
for use with D
WALT attachments.
e
DO nOT use this powerhead or any attachment for anything
other than its intended use described in this and the
attachments instructions.
For a complete list of recommended attachments contact
customer service.
8
6
on top of the handle
19
is
12
must
Assembling the Attachment to the
Powerhead (Fig. B)
1. The upper powerhead pole
latching holes
2. When installing the attachment pole
powerhead pole
the correct latching hole
instructions for details.
nOTE: To properly engage the latching button
the latching hole
pole
7
and move it axially until the latching button
engages the latching hole.
3. Turn the knob
4. See the attachment instructions for properly
assembled attachment.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
WARNING: Read the entire instruction manual for
each optional attachment prior to using with this
powerhead.
Installing and Removing the Battery Pack
(Fig. E)
nOTE: For best results, make sure your battery pack is
19
fully charged.
To install the battery pack
battery pack with the rails inside the tool's handle and slide it
into the handle until the battery pack is firmly seated in the
tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button
8
and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of this manual.
Proper Hand Position (Fig. J)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
WARNING: Hold the tool using only the designated
gripping surfaces: The powerhead handle and the
auxiliary handle.
WARNING: Do not use the pole as a gripping surface.
Proper hand position requires one hand on the powerhead
handle
4
and one hand on the auxiliary handle
7
is equipped with three
8
,
9
,
10
for the latching button
5
7
, align the latching button
8
. See specific attachment
8
, slightly rotate the powerhead
20
to secure the attachment.
7
into the tool handle, align the
21
.
into the upper
21
with
21
with
6
.
Publicité
Table des Matières
