Working Advice - Bosch UniversalGardenTidy Notice Originale

18 | English
Before any work on the product, disconnect supply
u
cord from the mains.
Connect the three parts of the vacuum tube (7). Take care
not to pinch your fingers during assembly.
Mount the vacuum tube (7) onto the motor unit. Insert the
vacuum tube (7) into the hinge on the motor unit. Raise the
vacuum tube (7) to align the fastening screw with main hous-
ing, and screw in the fastening screw (3) until fully tight and
clicks are heard to secure the vacuum tube.
Mount the collection bag (10) to the motor unit and attach
the bag clips to the hooks on the vacuum tube. Take care not
to pinch your fingers during assembly.
Mounting the shoulder strap (see figure H)
Fasten the shoulder strap (9) with both hooks (8) to the
shoulder -strap loops (13), Adjust the shoulder strap (9) so
that it comfortably carries the weight of the product and can
be guided easily.
Mounting and Adjusting the handle (see figures I
and J)
To attach the handle, place the handle (5) over the holders
on the tube, then insert the screw (6) though the handle and
tighten.
To adjust the angle then loosen the screw (6), move the
handle (5) up or down to the desired working position and
then tighten the screw (6) again.
Operating (see figures K, L and M)
Make sure that the cable is not in your way while working.
Fasten the cable in the cable holder on the side of the auxili-
ary handle. (see figure K)
To switch on, turn the On/Off switch (1) clockwise until it
clicks.
The airflow speed is variable. To increase the airflow speed,
turn the On/Off switch (1) clockwise.
To reduce the speed, turn the On/Off switch (1) anticlock-
wise.
Troubleshooting
Problem Possible Cause
Product does not run Components not assembled correctly
Power turned off
Mains socket faulty
Extension cable damaged
Fuse faulty / blown
Motor protector has activated
Product runs intermit- Extension cable damaged
tently
F 016 L81 834 | (21.03.2019)
To switch off, turn the On/Off switch (1) anticlockwise until
it clicks.
Set the On/Off switch (1) of the product to "0" before dis-
connecting the mains voltage or pulling the mains plug.
Direct the vacuum tube towards the debris that you want to
collect. If no debris is collected/moved, increase the airflow
speed.
Disassembling (see figures N and O)
Before carrying out any work on the product, discon-
u
nect supply cord from the mains.
To empty the collection bag (10), press button (11) and re-
move the collection bag (10). Remove the clips from the va-
cuum tube (7). Open the zip and empty the collection bag
(10) as required.
To disassemble, press button (11) and remove the collec-
tion bag (10). Remove the clips from the vacuum tube (7).
Take care not to pinch your fingers during disassembly.
Loosen the fastening screw (3). Remove the vacuum tube
(7) and store it securely.

Working Advice

When operating, always point the nozzle/vacuum tube to-
wards the ground.
Do not blow hot, flammable or explosive material.
The product is only suitable for foliage and garden waste.
Please inspect the area for little animals and hard objects be-
fore using the product.
Do not vacuum liquids, plastic bags, cans, pine cones,
branches larger than 5 mm (Ø > 5 mm), cloth, tissues and
pegs.
The motor will only start, if the following parts are assembled
correctly:
– vacuum tube and collection bag in vacuum mode
– nozzle and safety cover in blow mode
Corrective Action
see "assembly".
Turn power on.
Use another socket.
Inspect cable, replace if damaged.
Replace fuse.
Allow motor to cool down and check that fan is
not blocked.
Inspect cable, replace if damaged.
Bosch Power Tools