Replacing The Power Cable - EINHELL BT-MS 250 L Mode D'emploi

Anleitung_BT_MS_250_L_SPK1:_
Take the blade (5) off the inner flange and pull
out downwards.
Mount the new saw blade in reverse order and
fasten.
Important! The cutting bevel of the teeth, i.e. the
direction of rotation of the saw blade, has to
conform with the direction of the arrow marked
on the housing.
Clean the saw blade flanges thoroughly before
mounting the saw blade.
Reattach the movable blade guard (6) in reverse
order.
Before using the saw again, check that the safety
devices are in good working order.
Important: Every time that you change the saw
blade, check to see that it spins freely in the
groove of the turntable in both perpendicular and
45° angle settings.
7. Assembly
7.1 90° cross-cuts and 0° rotary table (Fig. 1)
To turn the machine on, simultaneously press
the main switch (3) and locking button (30).
Important! Place the material you want to saw
flat on the machine surface and secure with the
clamping device (19) so that the material cannot
move while you are cutting.
After switching on the saw, wait for the blade (5)
to reach its maximum speed.
Press the release lever (1) sideways and, using
the handle (2), apply steady and light downward
pressure to move the machine head through the
workpiece.
When the cut is completed, return the machine to
its top parking position and let go of the On/Off
switch.
Caution! A return spring causes the machine
head to rise automatically at the end of the cut.
Do not let go of the handle (2) as soon as the cut
is completed but steady the machine head and
allow it to rise slowly.
7.2 90° cross-cuts and 0°-45° rotary table (Fig.6)
The crosscut saw can be used to make right and left
angular cuts of 0°- 45° in relation to the stop rail.
Lift the machine head (4) to its top position.
Release the rotary table (8) by slackening the
locking handle (10) and pressing the latch (11).
Turn the rotary table (8) by its handle (2) to the
angle you want, i.e. the mark (a) on the rotary
table has to comply with the required angle
dimension (17) on the base plate (9).
Re-tighten the locking handle (10) in order to fix
the rotary table (8) in position.
30.12.2008 11:30 Uhr Seite 15
Make the cut as described in Section 7.1).
7.3 Mitre cuts 0°-45° and rotary table 0° (Fig. 4/7)
The crosscut saw can be used to make miter cuts of
0° - 45° in relation to the work face.
Lift the machine head (4) to its top position.
Fix the rotary table (8) in 0° position.
Undo the tightening screw (12) and use the
handle (2) to tilt the machine head (4) to the left
until the pointer (a) coincides with the required
angle value (15).
Re-tighten the locking nut (12) and make the cut
as described in Section 7.1).
7.4 Mitre cuts 0°-45° and rotary table 0°-45°
(Fig. 10)
The crosscut saw can be used to make miter cuts to
the left of 0°- 45° in relation to the work face and, at
the same time, 0° - 45° in relation to the stop rail
(double miter cut).
Lift the machine head (4) to its top position.
Undo the rotary table (8) by slackening the
locking handle (10) and pressing the latch (11).
Adjust the rotary table (8) by its handle (2) to the
required angle (see also Section 7.2).
Retighten the tightening screw (10) in order to
secure the turntable in place.
Undo the tightening screw (12) and use the
handle (2) to tilt the machine head (4) to the left
until it coincides with the required angle value (in
this connection see also section 7.3).
Screw the tightening screw (12) back down
again.
7.5 Laser function (Fig. 17)
You can switch the laser ON and OFF with the
switch (a).
The laser directs a beam onto the workpiece.
Extremely precise cuts can be made using the
laser function.
Replacing the battery (Fig. 18-19): Ensure that
laser (21) is switched off. Remove the battery
compartment cover (36). Remove the spent batteries
and replace them with new ones (2 x 1.5 V type R02,
LR 03 Micro, AAA). Check that the battery terminals
are positioned correctly. Close the battery
compartment again.

8. Replacing the power cable

If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its after-
sales service or similarly trained personnel to avoid
danger.
GB
15