Timberpro CS2500 Mode D'emploi page 5

20. Operate the chain saw only in well
ventilated areas. Never start or run
the engine inside a closed room or
building. Exhaust fumes contain dan-
gerous carbon monoxide.
21. Do not operate the chain saw in a tree
unless specially trained to do so.
22. Guard against kickback. Kickback is
the upward motion of the guide bar
which occurs when the saw chain at
the nose of the guide bar contacts
an object. Kickback can lead to dan-
gerous loss of control of the chain
saw.
23. When transporting your chain saw,
make sure the appropriate guide bar
scabbard is in place.
24. Never touch the muffer guard, guide
bar, saw chain or nut with bare hands
while the engine is in operation or im-
mediately after shutting down the
engine. Doing so could result in seri-
ous burns because of high tempera-
ture.
(3) (1) muffler guard
(2) guide bar
(3) saw chain
(2)
(1)
KICKBACK SAFETY PRECAUTIONS
FOR CHAIN SAW USERS
WARNING
• Kickback may occur when the nose
or tip of the guide bar touches an
object, or when the wood closes in
and pinches the saw chain in the cut.
Tip contact in some cases may cause
a l i g h t n i n g
reaction,kicking the guide bar up and
back towards the operator. Pinching
the saw chain along the top of the
guide bar may push the guide bar
rapidly back towards the operator.
Either of these reactions may cause
you to Iose control of the saw, which
could result in serious personal injury.
• Do not rely exclusively on the safety
devices built into your saw. As a chain
saw user you should take several
steps to keep cutting jobs free from
accident or injury.
(1) With a basic understanding of kick-
back you can reduce or eliminate the
element of surprise. Sudden surprise
contributes to accidents.
(2) Keep a good grip on the saw with
both hands, the right hand on the rear
WORSE EFFECTS OF VIBRATION
•
•
•
FOR PROTECTING YOUR BODY FROM VIBRATION
1. Always use the right tool for each job (to do the job
2. Check tools before using them to make sure they
f a s t r e v e r s e
3. Make sure cutting tools are kept sharp so that they
4. Reduce the amount of time you use a tool in one go,
5. Avoid gripping or forcing a tool or workpiece more
6. Store tools so that they do not have very cold handles
7. Encourage good blood circulation by:
•
•
DISPOSAL
•
•
GB 3
handle, and the left hand on the front
handle, when the engine is running.
Use a firm grip with thumbs and fin-
gers encircling the chain saw
handles. A firm grip will help you re-
duce kickback and maintain control
of the saw.
(3) Make certain that the area in which
you are cutting is free from obstruc-
tions. Do not let the nose of the guide
bar contact a log, branch, or any
other obstruction which could be hit
while you are operating the saw.
(4) Cut at high engine speeds.
(5) Do not overreach or cut above shoul-
der height.
(6) Follow the manufacturer's sharpening
and maintenance instructions for the
saw chain.
(7) Only use replacement bars and
chains specified by the manufacturer
or the equivalent.
If you continue to use high-vibration tools these
symptoms will probably get worse, for example:
the numbness in your hands could become perma-
nent and you won't be able to feel things at all;
you will have difficulty picking up small objects such
as screws or nails;
the vibration white finger could happen more fre-
quently and affect more of your fingers.
Please observe the following matter, in order to pro-
tect the health of your body.
more quickly and expose you to less hand-arm vi-
bration).
have been properly maintained and repaired to avoid
increased vibration caused by faults or general wear.
remain efficient.
by doing other jobs in between.
than you have to.
when next used.
keeping warm and dry (when necessary, wear
gloves, a hat, waterproofs and use heating pads if
available);
giving up or cutting down on smoking because
smoking reduces blood flow; and massaging and
exercising your fingers
When you dispose of the machine, do not disas-
semble the machine.
When you dispose of the machine, fuel, chain oil,
be sure to follow your local regulations.