Husqvarna AUTOMOWER 435X AWD Guide Rapide page 3

For more information and instructions, read the complete Operator 's manual on the Husqvarna
website (w w w.husqvarna.com).
1. PL AC E M E N T O F A N D CO N N EC T I N G T H E C H A RG I N G S TAT I O N
1. Place the charging station with a lot of open space in front of the charging station and on a relatively horizontal surface.
2. Connect the power supply's low voltage cable to the charging station and the power supply.
3. Connect the power supply to a 100-240 V wall socket.
4. Place the product in the charging station to charge the battery while the boundary wire is laid. Start the product.
2. PL AC E M E N T O F T H E B O U N DA RY W I R E A N D T H E G U I D E W I R E
1. Lay the boundary wire so that it forms a loop around the work area.
2. Make an eyelet at the point where the guide wire will later be connected.
3. Run the guide wire to the point on the boundary loop where the connection will be made. Avoid laying the wire at tight angles.
4. For minimum distance to obstacles and islands, see illustration (number 5).
3. CO N N EC T I N G T H E B O U N DA RY W I R E A N D T H E G U I D E W I R E
1. Narrow passages in the yard make it difficult for the product to find the charging station. The product can be lead to remote
areas using the guide wire. The guide wire also helps the product to quickly find the charging station.
2. Lay the guide wire under the charging station and at least 2 m / 7 ft straight out from the front edge of the charging station.
3. Open the connectors and lay the wire ends in the recesses on each connector.
4. Press the connectors together using a pair of pliers.
5. Cut 1-2 cm / 0.4-0.8 in. above the connectors.
6. Press the boundary connectors onto the contact pins, marked AL (left) and AR (right), on the charging station. It is important
that the right-hand wire is connected to the right-hand contact pin, and the left-hand wire to the left-hand pin.
7. Fasten the guide connector to the contact pin marked G1 on the charging station. Additional guides the similar way.
4. CO N N EC T I N G T H E G U I D E W I R E TO T H E B O U N DA RY W I R E
1. Cut the boundary wire with a wire cutters at the centre of the eyelet that was made in step 2.2.
2. Connect the guide wire to the boundary wire using the accompanying couplers. Press the couplers completely together with
a pair of pliers.
S TA R T I N G A N D S TO PPI N G
STARTING
1. Push the START button.
2. Push the jog wheel to confirm and the product starts.
STOPPING
Push the STOP button.
A D J U S T I N G T H E PRO D U C T TO S U I T T H E S I Z E O F YO U R L AW N
Adjust the mowing time to suit your yard using the Schedule function. The product cuts approximately 146 m² / 1570 ft² per
hour and day. For example, if your yard comprises 1200 m² / 12900 ft² of grass, the product should work 8 hours a day.
M A I N T E N A N C E
1. The product must be turned off before any maintenance is done, such as cleaning or replacing the blades. The product is
disabled when the LED indicator lamp at the jog wheel is not lit. Replace the blades regularly for the best mowing result.
2. Never use a high-pressure washer or even running water to clean the product. Never use solvents for cleaning.
3. All connections to the charging station (power supply, boundary and guide wire) must be disconnected if there is a risk of a
thunderstorm.
4. Fully charge the battery at the end of the season before winter storage.
P25_QG_1140537_435X_AWD_2020.indd 3 P25_QG_1140537_435X_AWD_2020.indd 3
E N
2019-12-13 7:24:19 2019-12-13 7:24:19