Applications; Suitable Fog Fluid; Switching On And Off - IMG STAGELINE FM-200H Mode D'emploi

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

3 Applications

The hazer FM-200H vaporizes fog fluid to produce arti-
ficial fog which can be used to enhance lighting effects
(e. g. in discotheques, on stage, in party rooms). A fan
inside the hazer distributes the fog in the room so that
a very fine, translucent haze is created.
The unit can be operated with or without the sup-
plied cable remote control. Alternatively, use a con-
troller with DMX512 protocol to operate the FM-200H.
Thus, the hazer can be integrated into a professional
lighting system without any difficulty.
4 Filling up the Tank with Fog Fluid
WARNING 1. Before filling up the tank with fog
fluid, always disconnect the unit from
the power supply!
2. Never add flammable fluids of any
kind to the fog fluid. Explosion haz-
ard!
3. The unit is not splash-proof. If fluid
gets inside the unit, it must be
cleaned and checked by skilled per-
sonnel before it is operated.
1) Unscrew the tank cap (13).
2) Fill up the tank with fog fluid (
sure that no fluid gets inside the unit. If any fluid is
spilt, wipe it off immediately with a cloth.
3) Screw on the cap to close the tank tightly.

4.1 Suitable fog fluid

The following fog fluids from "img Stage Line" suitable
for the hazer are available in 5 litre containers:
Item
Feature
NF-502L
long haze effect
NF-502SL
extra-long haze effect
Only use the fog fluids listed above. If you use other
fluids, no liability will be accepted for correct operation.
chapter 4.1). Make
Order No.
38.1820
38.1830
5 Operation
5.1 Setting up or suspending the unit
Remove all packaging material. Make sure that there
are no packaging remnants at the fog output nozzle or
on the housing.
G
The heat produced inside the unit must be dissi-
pated by air circulation. Make sure that a minimum
space of 50 cm is provided around and above the
unit and that the air vents of the housing are not
covered.
G
Never touch the fog output nozzle; it gets very hot
during operation. Always ensure a distance of 3 m
to easily flammable material or explosive material.
G
Never direct the haze outlet at persons – risk of
burns!
Place the unit on a horizontal surface (not directly on a
carpet or wooden floor!) or install it via its bracket (12)
[e. g. on a crossbar with a mounting clip]. For precise
horizontal adjustment of the unit, slightly release the
screws (5) on both sides of the mounting bracket,
readjust the position of the unit and then fasten the
screws.
WARNING Install the unit safely and expertly.
When installing it at a place where
people may walk or sit under it, addi-
tionally secure it (e. g. via a safety rope
on the mounting bracket; fasten the
safety rope in such a way that the max-
imum falling distance of the unit will not
exceed 20 cm).

5.2 Switching on and off

WARNING 1. The fog output nozzle gets very hot.
Never touch it during operation or
shortly after operation. Risk of burns!
2. The unit is for adult use only. Never
leave it unattended during operation.
3. Never operate the hazer without fog
fluid; otherwise there will be a fire
hazard due to overheating. Besides,
the unit may be damaged.
1) Before connecting the unit to a mains socket:
1. If necessary, wring out the sponge that is used to
soak up drops leaking from the fog output noz-
zle.
2. Check the fluid level of the tank and fill up fog
fluid, If necessary (
2) First connect the supplied mains cable to the mains
jack (9), then connect it to a mains socket (230 V~ /
50 Hz).
chapter 4).
GB
9

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

38.6450

Table des Matières