Bosch EasyImpact 500 Notice Originale page 19

Impact drilling into concrete:
a
h
K
Screwdriving:
a
h
K
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Auxiliary Handle (see figure A)
Do not operate your power tool without the auxiliary
u
handle (20).
Before carrying out any work, make sure that the wing
u
bolt (21)/(18) is tightened. Loss of control can cause
personal injury.
Turn the wing bolt (21)/(18) anticlockwise and guide the
auxiliary handle (20) in the required position over the drill
chuck onto the spindle collar of the power tool.
You can swivel the auxiliary handle (20) in order to achieve a
safe work posture that reduces fatigue.
Swivel the auxiliary handle (20) to the required position and
retighten the wing bolt (21)/(18) by turning it clockwise.
Setting the drilling depth (see figure B)
You can use the depth stop (23) to set the required drilling
depth X.
Press the button for depth stop adjustment (22) and insert
the depth stop into the auxiliary handle (9).
Bosch Power Tools
EasyImpact EasyImpact
5500 570
2
m/s 32
2
m/s 4.0
2
m/s < 2.5 < 2.5
2
m/s
1.5
The fluting on the depth stop (23) must face downwards.
Pull the depth stop far enough out that the distance between
the drill bit tip and the edge of the depth stop corresponds
to the required drilling depth X.
Drill Assistant
Applying the Drill Assistant (see figures C–D)
The Drill Assistant (10) can be used with and without the
dust collection device (13). Use of the dust collection
device (13) is limited to drill bits with a diameter of 12 mm
and a length of 120 mm.
Attach the dust collection device (13) to the adapter (26).
Press the unlocking button (8) to release the Drill Assist-
ant (10) from its parked position.
Guide the Drill Assistant (10) over the drill chuck onto the
spindle collar of the power tool.
Lock it by turning the wing bolt (18) clockwise.
Setting the Drilling Depth (see figures E–F)
Attach the drill bit (see section "Changing the Tool").
You can use the setting ring (17) to set the required drilling
depth X.
Unlock the setting ring (17) by turning it to the left
Place the dust container (11) or the adapter (26) flush
against the wall or workpiece. Move the tip of the drill bit to
the wall or workpiece.
Slide the setting ring (17) backwards until the distance
matches the required drilling depth X or place a wall plug on
the rail and slide the setting ring (17) backwards to the wall
plug. Lock the setting ring (17) by turning it to the right .
Take the wall plug out of the rail again. The drilling depth now
matches the set length X on the rail.
Note: It is important to have the exact drilling depth when
using wall plugs. If the drilled hole is too deep, the wall plug
will slip too far into the wall or workpiece. If the hole is too
small, the wall plug will stick out.
Emptying the dust container (see figure G)
The dust container (11) is enough for drilling about 25 holes
in masonry at a drilling depth of 30 mm with a drill bit dia-
meter of 6 mm.
To remove the dust container (11), press the side-mounted
unlocking buttons (12) and pull the dust container off down-
wards.
English | 19
EasyImpact EasyImpact
5700 6000
28 28 28
2.0 2.0 2.0
< 2.5 < 2.5
1.5 1.5 1.5
.
1 609 92A 5V1 | (14.07.2020)