Update Software; Important Notices - Reskal LD550 Notice D'utilisation

SLEEP (Power Saving) MODE
The detector will enter sleep mode after 5 minutes of idling in order to
save power. The information on the display window will turn off and only
the blue ON/OFF indicator lights up. The machine can be waken up and
return to working mode by touching any key or feeding a banknote.
When the machine is in sleep mode with only built-in battery, if the
machine is idle for more 15 minutes again, the machine will power off
automatically.
BATTERY STATUS MESSAGE
When the machine is charging the battery, the Number of Sheets Display
will display «–Ch» at an interval to indicate the charging status. Usually it
needs about 15 hours or more to make the power of battery fully.
If the voltage is low, the Number of Sheets Display will display «-Lo» at
an interval to remind the user of that the battery needs to be charged or
the user should turn off the banknote detector.

UPDATE SOFTWARE

Through SD card update software
1. Connect the Micro-SD card to PC by
a card reader,
Run « CreateDiskImage.exe » on PC.
2. Select « IMAGE_2_DISK » option, and select
the corresponding card drive in the «disk»
option that connects the Micro-SD card to PC.
TROUBLESHOOTING
Self test error code display
The detector automatically performs a self test after power on. If one of
the following error messages is displayed on the display window, usually
it is because the sensor is blocked by banknotes or dust. Please use a
brush or a piece of soft cloth to clean the dust on the sensor or remove
the banknotes, and then restart the machine.
Error message display
P01
P02
P03
P04
P05
P06
P09
P10
P11
P12
Detective Error Code Display
If the following error code is displayed on the display window during the
course of detecting, you can handle them as per the error type after the
machine is stopped.
Error type
The upper left IR sensor is failure
The upper right IR sensor is failure
The below left IR sensor is failure
The below right IR sensor is failure
The feeding sensor is failure
The rotate speed sensor is failure
The left passing sensor is failure
The right passing sensor is failure
The magnetic sensor is failure
No debug the machine
3. Click « OPEN » button to select the « .ISO »
file that you want to download.
4. Click « Xfer » button, it will start to
download the file, if you download succesfully,
it will the following interface :
Insert the Micro-SD card into Micro-SD socket,
next connect the machine to the external power
source.
Press and hold «CLR» key and «ON/OFF»
key to turn on the machine, the machine will display seven «-», it
shows the machine has already entered into download mode. After the
completion of the update, the machine will beep 2 for times and turn off
automatically.
Through USB update software
1. Turn off the banknote detector first, and then use the provided
download cable to connect the USB port on PC and the USB port of the
detector together.
2. Put the DC output plug into the DC socket.(make sure that the adapter
is inserted into the mains). Next, press «CLR» key and «ON/OFF» key si-
multaneously. If seven pieces of «-» are displayed on the Display Window,
it shows the machine has entered into download mode. If the display win-
dow doesn't display seven pieces of «-», please retry 1 and 2 steps again.
3. Run «Auto Download software» on PC and click «LoadFile» button to
load the update software(***.UPL)(See Figure 4), then click «Update Soft»
button to download the software(See Figure 5)
4. If you download successfully(See Figure 6), the machine will turn off
automatically.
! Notice : Single battery can't download software.
9
Error message display
E01
E02 / E03
E04 / E05
E06
E07
E08
E09 / E10 / E11 / E12
E14
E20

IMPORTANT NOTICES

• If the machine keeps alarm or works abnormally, check the following:
- Whether the main power supply is within specified range (AC
100V~240V/50~60Hz).
- Whether the DC output is within specified range: DC 12V±10%.
- Whether the supply plug is well connected.
- Whether the built-in battery is sufficient to work.
- Keep away from strong magnetic affection.
- Clear the dust on the sensors.
• If a banknote is blocked while it is being detected, please open the top
cover and get out the banknote to detect it again.
• Please smooth the banknote before detecting, and the banknote must
be put in straightly while it is being inserted.
10
Error type
Length Error
Magnetic feature Error
IR feature Error
Thickness Error
Slant note
Hologram Error
Paper quality Error
Denomination Error
Passing Error