Window Meanings - Varian Turbo-V 81-AG Notice De Mode D'emploi

Examples:
Command: START
Source: PC
Destination: Controller
02 80 30 30
STX ADDR WINDOW
Source: Controller
Destination: PC
02 80 06 03
STX ADDR ACK ETX
Command: STOP
Source: PC
Destination: Controller
02 80 30 30
STX ADDR WINDOW
Source: Controller
Destination: PC
02 80 06 03
STX ADDR ACK ETX
Command: SOFT-START (ON)
Source: PC
Destination: Controller
02 80 31 30
STX ADDR WINDOW
Source: Controller
Destination: PC
02 80 06 03
STX ADDR ACK ETX
Command: SOFT-START (OFF)
Source: PC
Destination: Controller
02 80 31 30
STX ADDR WINDOW
Source: Controller
Destination: PC
02 80 06 03
STX ADDR ACK ETX
Command: READ PUMP STATUS
Source: PC
Destination: Controller (with address = 3)
02 83 32 30
STX ADDR WINDOW
Source: Controller (with address = 3 in stop status)
Destination: PC
02 83 32 30 35 30 30 30 30 30 30 03
STX ADDR WINDOW DATA (STATUS)
Command: READ SERIAL TYPE
Source: PC
Destination: Controller (with address = 3 in 485 mode)
02 83 35 30
STX ADDR WINDOW
Source: Controller
Destination: PC
02 83 35 30 34
STX ADDR WINDOW
30 31 31 03 42
WR ON ETX CRC
38 35
CRC
30 31 30 03 42
WR OFF ETX CRC
38 35
CRC
30 31 31 03 42
WR ON ETX CRC
38 35
CRC
30 31 30 03 42
WR OFF ETX CRC
38 35
CRC
35 30 03 38 37
RD ETX CRC
38
ETX CRC
34 30 03 38 31
RD ETX CRC
30 31 03 42
RD DATA ETX CRC

Window Meanings

N. Read/
Write
33
000 R/W
001 R/W
32
008 R/W
100 R/W
101 R/W
32
102 R/W
103 R/W
33
104 R/W
105 R/W
37 106 R/W
107 R/W
108 R/W
30
109 W
48/50
TECHNICAL INFORMATION
Data Description
Type
L Start/Stop Start = 1
(in remote/ Stop = 0
mode the win-
dow is read
only)
L Low Speed No = 0
Activation (in Yes = 1
remote/ mode (default = 0)
the window is
read only)
L Remote Remote = 1
or Serial con- Serial = 0
figuration
(default = 1)
L Soft Start YES = 1
(write only NO = 0
in Stop
(default = 0)
condition)
N R1 Set Point 0 = Fre-
type quency
1 = Power
2 = Time
3 = Normal
4 =Pressure
(default = 0)
N R1 Set Point (default =
valve 867)
(expressed in
Hz, W or s)
N Set Point delay: 0 to 999999
time between
(default = 0)
pump start and
the set point
check (sec-
onds)
L Set Point sig- 0 = high level
nal activation active
type: the sig- 1 = low level
nal can be active
"high level ac-
(default = 0)
tive" or "low
level active"
N Set point 0 to 100
hysteresis
(default = 2)
(in % of value)
L Water cooling 0 = NO
(write only in 1 = YES
stop)
L Active Stop 0 = NO
(write only in 1 = YES
stop)
(default = 0)
N Baud rate 600 = 0
1200 = 1
2400 = 2
4800 = 3
9600 = 4
(default = 4)
L Pump life/ To reset,
cycle time/ write '1'
cycle number
reset
87-901-004-01 (B)
Permitted
Values